{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"6AG1136-6DB00-2CA0","brand":"Siemens","brandSlug":"siemens","productSlug":"6AG1136-6DB00-2CA0","canonicalUrl":"https://aoctrl.com/siemens/6AG1136-6DB00-2CA0","factsUrl":"https://aoctrl.com/api/mcp/products/6AG1136-6DB00-2CA0","rawCanonicalId":null},"summary":{"shortDescription":"Siemens SIPLUS 6AG1136-6DB00-2CA0 digital output module, 24 V DC, transistor type, 5-byte I/O, 6 A max per module (2 A per channel), width 15 mm, SIL 3 capable.","salesMarkdown":"## Module overview This 6AG1136-6DB00-2CA0 is a SIPLUS ET 200SP digital output module delivering transistor outputs at 24 V DC nominal. It provides 5-byte input and 5-byte output data to the controller, with each channel rated for 2 A continuous (derated per ambient). The module draws 21 mA from the backplane bus and dissipates 4 W typical. Overload and short-circuit protection are built in, with a typical response threshold of 2.9 A. Open-circuit detection is supported for each channel. Diagnostic alarms and a red ERROR LED enable fast fault isolation. ## Thermal and mounting considerations Shielded cable runs up to 1 000 m; unshielded up to 500 m. Load resistance: 12 Ω min, 2 000 Ω max. Compliance documentation is issued by Siemens upon shipment; the module carries a type test isolation of 707 V DC.","metaTitle":"Siemens 6AG1136-6DB00-2CA0 Digital Output Module, 24V DC","metaDescription":"Active ET 200SP transistor output module, 24V DC, 2A per channel, 6A per module, SIL 3. 15mm wide, fully traceable from authorized stock.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["PLCs (Programmable Logic Controllers)"],"specifications":{"Depth":"58 mm","Width":"15 mm","title":"6AG1136-6DB00-2CA0","Height":"73 mm","Inputs":"5 byte","Outputs":"5 byte","RUN LED":"Yes; green LED","I&M data":"Yes; I&M0 to I&M3","ERROR LED":"Yes; red LED","Lower Limit":"12 Ω","Upper Limit":"2 000 Ω","description":"SIPLUS ET 200SP F-DQ 4x24VDC/2A PM HF based on 6ES7136-6DB00-0CA0 with conformal coating, -30…+60 °C, fail-safe digital outputs up to PL e (ISO 13849), up to SIL 3 (IEC 61508)","Shielded, Max.":"1 000 m","Weight, approx.":"57 g","lifecycle_stage":"current","Diagnostic alarm":"Yes","Power loss, typ.":"4 W","Rated value (DC)":"24 V","Unshielded, Max.":"500 m","usable BaseUnits":"BU type A0","FW update possible":"Yes","On Lamp Load, Max.":"10 Hz; Symmetrical","up to 40 °C, max.":"6 A; note derating data in the manual","up to 50 °C, max.":"4 A; note derating data in the manual","up to 60 °C, max.":"4 A; note derating data in the manual","up to 70 °C, max.":"4 A; note derating information in the manual; only with configured slots to the left and right of the module","Overload protection":"Yes","Between The Channels":"No","Diagnostics function":"Yes","For Signal \"1\", Min.":"24 V; L+ (-0.5 V)","Isolation tested with":"707 V DC (type test)","SIL acc. to IEC 61508":"SIL 3","Channel status display":"Yes; green LED","For Module Diagnostics":"Yes; green/red DIAG LED","Open-circuit detection":"Yes","Type of digital output":"Transistor","For Channel Diagnostics":"Yes; red LED","Current per module, max.":"6 A; note derating data in the manual","Response threshold, typ.":"2.9 A","Short-circuit protection":"Yes","Current consumption, max.":"21 mA; From the backplane bus","Current per channel, max.":"2 A; note derating data in the manual","Number of digital outputs":"4","With Inductive Load, Max.":"0.1 Hz; according to IEC 60947-5-1, DC-13, symmetrical","With Resistive Load, Max.":"30 Hz; Symmetrical","For Signal \"1\" Rated Value":"2 A","Reverse polarity protection":"Yes","Vertical Installation, Max.":"50 °C; = Tmax","Vertical Installation, Min.":"-30 °C; = Tmin","Horizontal Installation, Max.":"60 °C; = Tmax; +70 °C with configured empty slots to the left and right of the module","Horizontal Installation, Min.":"-30 °C; = Tmin (incl. condensation/frost)","Substitute values connectable":"No","Suitable for safety functions":"Yes","Digital outputs, parameterizable":"Yes","Current consumption (rated value)":"75 mA; without load","permissible range, lower limit (DC)":"20.4 V","permissible range, upper limit (DC)":"28.8 V","For Signal \"0\" Residual Current, Max.":"0.5 mA","Between The Channels And Backplane Bus":"Yes","Power available from the backplane bus":"70 mW","Monitoring of the supply voltage (PWR-LED)":"Yes; green PWR LED","Performance level according to ISO 13849-1":"PLe","Installation altitude above sea level, max.":"4 000 m","Limitation of inductive shutdown voltage to":"typ. 2*47V","Protection against fouling acc. to EN 60664-3":"Yes; Type 1 protection","Low demand mode: PFDavg in accordance with SIL2":"< 2.00E-04","Low demand mode: PFDavg in accordance with SIL3":"< 2.00E-05","Ambient air temperature-barometric pressure-altitude":"Restrictions for installation altitudes > 2 000 m, see entry ID: 109771992","High demand/continuous mode: PFH in accordance with SIL2":"< 1.00E-08 1/h","High demand/continuous mode: PFH in accordance with SIL3":"< 1.00E-09 1/h","Color code for module-specific color identification plate":"CC02","Resistant to commercially available coolants and lubricants":"Yes; Incl. diesel and oil droplets in the air","Between The Channels And The Power Supply Of The Electronics":"No","Environmental conditions for process, measuring and control systems acc. to ANSI/ISA-71.04":"Yes; Level GX group A/B (excluding trichlorethylene; harmful gas concentrations up to the limits of EN 60721-3-3 class 3C4 permissible); level LC3 (salt spray) and level LB3 (oil)","Qualification and Performance of Electrical Insulating Compound for Printed Board Assemblies according to IPC-CC-830A":"Yes; Conformal coating, Class A"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$391.16","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/e51396e92b3a763c69906944371f4bb2.pdf","sourceUrl":"https://support.industry.siemens.com/webbackend/api/ProductSupport/TechnicalData?language=en&region=cn&productId=76635&mlfb=6AG1136-6DB00-2CA0"},"ai":{"faq":[{"question":"What is the width of this module?","answer":"15 mm, making it one of the narrowest ET 200SP output modules."},{"question":"What base unit does it require?","answer":"It mounts on BU type A0 base units."},{"question":"Does it support diagnostic alarms?","answer":"Yes, diagnostic alarm is enabled, and there are per-channel red LEDs for fault indication."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/siemens/6AG1136-6DB00-2CA0","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/siemens/6AG1136-6DB00-2CA0 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}