{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"6ES7132-6BH00-0AA0","brand":"Siemens","brandSlug":"siemens","productSlug":"6ES7132-6BH00-0AA0","canonicalUrl":"https://aoctrl.com/siemens/6ES7132-6BH00-0AA0","factsUrl":"https://aoctrl.com/api/mcp/products/6ES7132-6BH00-0AA0","rawCanonicalId":null},"summary":{"shortDescription":"Siemens ET 200SP digital output module, 6ES7132-6BH00-0AA0, 2-byte DQ, 24 VDC rated, 8 A continuous up to 60 °C, diagnostic alarm, BU type A0 base unit.","salesMarkdown":"## ET 200SP digital output slice — what it fits The 6ES7132-6BH00-0AA0 is a 2-byte digital output module for the Siemens ET 200SP distributed I/O system. It provides 16 channels of 24 VDC current-sourcing outputs rated 8 A total continuous current at up to 60 °C ambient. It requires a BU type A0 base unit — the mechanical and electrical backplane interface that carries the module and connects it to the ET 200SP bus. The base unit supports 1-wire connection directly; for 2-, 3-, or 4-wire sensors, add a potential distributor module. ## Switching performance and diagnostics Typical turn-on time is 80 µs at rated load, maximum 150 µs; turn-off is 100 µs typical, 200 µs maximum. This suits fast solenoid or contactor banks where cycle time matters. Diagnostic alarm and group error reporting are built in — the module signals a short-circuit or wire-break condition to the controller. I&M data (I&M0 to I&M3) is supported for asset tracking and firmware version identification. Power dissipation is 1 W typical. Maximum cable length is 1 000 m shielded, 600 m unshielded. No official pin-compatible replacement exists within the ET 200SP family — the 6ES7132-6BH00-0AA0 is the current 2-byte DQ variant with 8 A continuous rating. Older ET 200S output modules use a different form factor and base unit; they are not mechanically interchangeable.","metaTitle":"Siemens 6ES7132-6BH00-0AA0 Digital Output Module, 24 VDC","metaDescription":"Siemens 6ES7132-6BH00-0AA0 ET 200SP digital output module, 2-byte DQ, 24 VDC, 8 A continuous, diagnostic alarm, BU type A0 base unit required.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Digital Output Modules"],"specifications":{"DQ":"Yes","MSO":"No","PWM":"No","Depth":"58 mm","Width":"15 mm","Height":"73 mm","Outputs":"2 byte","I&M data":"Yes; I&M0 to I&M3","Wire-break":"No","Group error":"Yes","Lower Limit":"48 Ω","Upper Limit":"100 kΩ","For Uprating":"No","Oversampling":"No","Short-circuit":"No","Shielded, Max.":"1 000 m","Current-sinking":"No","Weight, approx.":"30 g","lifecycle_stage":"current","\"0\" To \"1\", Max.":"150 µs; at rated load","\"0\" To \"1\", Typ.":"80 µs; at rated load","\"1\" To \"0\", Max.":"200 µs; at rated load","\"1\" To \"0\", Typ.":"100 µs; at rated load","Current-sourcing":"Yes","Diagnostic alarm":"Yes","Firmware version":"V0.0","Isochronous mode":"No","Power loss, typ.":"1 W","Rated value (DC)":"24 V","Unshielded, Max.":"600 m","usable BaseUnits":"BU type A0","1-Wire Connection":"BU type A0","2-Wire Connection":"BU type A0 + Potential distributor module","3-Wire Connection":"BU type A0 + Potential distributor module","4-Wire Connection":"BU type A0 + Potential distributor module","Automatic encoding":"Yes","FW update possible":"No","On Lamp Load, Max.":"10 Hz","up to 50 °C, max.":"8 A","up to 60 °C, max.":"8 A","Between The Channels":"No","Diagnostics function":"Yes","HW functional status":"From FS03","Isolation tested with":"707 V DC (type test)","Channel status display":"Yes; green LED","For Module Diagnostics":"Yes; green/red DIAG LED","Open-circuit detection":"No","Type of digital output":"Source output (PNP, current-sourcing)","For Channel Diagnostics":"No","Current per module, max.":"8 A","Response threshold, typ.":"1.4 A; 0.7 to 1.9 A","Short-circuit protection":"Yes","Current consumption, max.":"55 mA; without load","Current per channel, max.":"0.5 A","Mechanical coding element":"Yes","Number of digital outputs":"16","With Inductive Load, Max.":"2 Hz","With Resistive Load, Max.":"100 Hz","For Signal \"1\" Rated Value":"0.5 A","Controlling a digital input":"Yes","Reverse polarity protection":"Yes","Vertical Installation, Max.":"50 °C","Vertical Installation, Min.":"-30 °C","Horizontal Installation, Max.":"60 °C","Horizontal Installation, Min.":"-30 °C","Monitoring the supply voltage":"Yes","Substitute values connectable":"Yes","Suitable for safety functions":"No","DQ with energy-saving function":"No","For Redundant Control Of A Load":"Yes","Digital outputs, parameterizable":"Yes","Type of mechanical coding element":"Type A","permissible range, lower limit (DC)":"19.2 V","permissible range, upper limit (DC)":"28.8 V","For Signal \"0\" Residual Current, Max.":"30 µA","Between The Channels And Backplane Bus":"Yes","PROFIBUS from GSD version/GSD revision":"One GSD file each, Revision 3 and 5 and higher","PROFINET from GSD version/GSD revision":"GSDML V2.3","Monitoring of the supply voltage (PWR-LED)":"Yes; green PWR LED","Installation altitude above sea level, max.":"5 000 m; Restrictions for installation altitudes > 2 000 m, see manual","Limitation of inductive shutdown voltage to":"Typ. L+ (-53 V)","STEP 7 configurable/integrated from version":"STEP 7 V5.5 or higher","STEP 7 TIA Portal configurable/integrated from version":"V14","Suitable for safety-related tripping of standard modules":"No","Color code for module-specific color identification plate":"CC00"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$72.39 – $203.13","priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/02d31e1dbbe2212235e83de9b37c4036.pdf","sourceUrl":"https://support.industry.siemens.com/webbackend/api/ProductSupport/TechnicalData?language=en&region=cn&productId=1091572&mlfb=6ES7132-6BH00-0AA0","alternativesUrl":"https://aoctrl.com/api/mcp/products/6ES7132-6BH00-0AA0/alternatives.json"},"ai":{"faq":[{"question":"What are the diagnostics features of 6ES7132-6BH00-0AA0?","answer":"It supports diagnostic alarm and group error reporting. I&M data (I&M0 to I&M3) is available for asset identification."},{"question":"Can 6ES7132-6BH00-0AA0 replace an older ET 200S output module?","answer":"No — the ET 200S and ET 200SP use different base units and backplane form factors. The 6ES7132-6BH00-0AA0 is specific to the ET 200SP system."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/siemens/6ES7132-6BH00-0AA0","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/siemens/6ES7132-6BH00-0AA0 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}