{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"6ES7136-6BA01-0CA0","brand":"Siemens","brandSlug":"siemens","productSlug":"6ES7136-6BA01-0CA0","canonicalUrl":"https://aoctrl.com/siemens/6ES7136-6BA01-0CA0","factsUrl":"https://aoctrl.com/api/mcp/products/6ES7136-6BA01-0CA0","rawCanonicalId":null},"summary":{"shortDescription":"Siemens ET 200SP fail-safe digital input module, 6ES7136-6BA01-0CA0, 8 inputs, 24 V DC, SIL 3, 15 mm width, current production.","salesMarkdown":"## Safety-rated input slice for ET 200SP This 6ES7136-6BA01-0CA0 is an ET 200SP fail-safe digital input module (F-DI 8×24V) rated SIL 3 per IEC 61508, meaning it can be used in safety functions up to that integrity level — emergency stops, light curtain monitoring, or two-hand control circuits where the machine must detect a fault within the safety reaction time. It takes 8 digital inputs at 24 V DC nominal, with a signal \"1\" threshold of +15 to +30 V and a signal \"0\" range of -30 to +5 V, so it works with standard 24 V sensors and NPN/PNP field devices as long as the common reference is set correctly. ## Signal timing and diagnostic coverage Input filtering is parameterizable between 0.4 ms and 20 ms for both rising and falling edges — the 0.4 ms minimum lets you catch fast sensor pulses (e.g., from a proximity switch on a high-speed indexing conveyor), while the 20 ms maximum debounces mechanical contacts without a separate filter block. Diagnostic coverage includes a per-channel status LED (green), a module diagnostics LED (green/red DIAG), and a red channel-error LED — the diagnostic alarm reports wire-break or short-circuit to the safety CPU, which can trigger a safe state without polling each input. Galvanic isolation is tested at 707 V DC type test between channels and the backplane bus, so a fault on one field circuit won't propagate to the rest of the rack. Shielded cable runs up to 1000 m are allowed; unshielded up to 500 m, so you can place the module near the field devices in a local cabinet rather than pulling long sensor cables back to the main panel. The 24 V DC supply draws 40 mA without load and the module dissipates 2 W typical, so the station power budget needs to account for this slice plus the BaseUnit's own consumption. I&M data (I&M0 to I&M3) is supported, so the module identifies itself to TIA Portal and the HMI for asset tracking without manual label checks.","metaTitle":"Siemens 6ES7136-6BA01-0CA0 ET 200SP F-DI 8×24V, SIL 3","metaDescription":"Siemens 6ES7136-6BA01-0CA0 ET 200SP fail-safe digital input module, 8 inputs, 24 V DC, SIL 3, active production. Sourced to order against RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["PLC Communication Modules"],"specifications":{"24 V":"Yes; min. L+ (-1.5 V)","Depth":"58 mm","Width":"15 mm","title":"6ES7136-6BA01-0CA0","Height":"73 mm","Inputs":"7 byte; S7-300/400F CPU, 6 byte","Outputs":"5 byte; S7-300/400F CPU, 4 byte","RUN LED":"Yes; green LED","I&M data":"Yes; I&M0 to I&M3","ERROR LED":"Yes; red LED","description":"SIMATIC DP, electronic module for ET 200SP, F-DI 8x 24 V DC HF, 15 mm width, up to PLe (ISO 13849-1)/ SIL3 (IEC 61508)","For Signal \"0\"":"-30 to +5 V","For Signal \"1\"":"+15 to +30 V","Shielded, Max.":"1 000 m","Parameterizable":"No","Weight, approx.":"29 g","lifecycle_stage":"current","Diagnostic alarm":"Yes","Power loss, typ.":"2 W","Rated value (DC)":"24 V","Unshielded, Max.":"500 m","usable BaseUnits":"BU type A0","Number of outputs":"8","Source/sink input":"Yes; P-reading","Automatic encoding":"Yes","FW update possible":"Yes","Hardware interrupt":"No","At \"0\" To \"1\", Max.":"20 ms","At \"0\" To \"1\", Min.":"0.4 ms","At \"1\" To \"0\", Max.":"20 ms","At \"1\" To \"0\", Min.":"0.4 ms","Between The Channels":"No","Diagnostics function":"Yes","For Signal \"1\", Typ.":"3.7 mA","Isolation tested with":"707 V DC (type test)","SIL acc. to IEC 61508":"SIL 3","Channel status display":"Yes; green LED","For Module Diagnostics":"Yes; green/red DIAG LED","For Channel Diagnostics":"Yes; red LED","Number of digital inputs":"8","Short-circuit protection":"Yes; Electronic (response threshold 0.7 A to 1.8 A)","Current consumption, max.":"40 mA; without load","Reverse polarity protection":"Yes","Vertical Installation, Max.":"50 °C","Vertical Installation, Min.":"0 °C","Horizontal Installation, Max.":"60 °C","Horizontal Installation, Min.":"0 °C","Suitable for safety functions":"Yes","Output current per module, max.":"800 mA; Total current of all encoders","Electronic coding element type F":"Yes","Output current per channel, max.":"300 mA","Category according to ISO 13849-1":"Cat. 4","Reparameterization possible in RUN":"No","permissible range, lower limit (DC)":"19.2 V","permissible range, upper limit (DC)":"28.8 V","Between The Channels And Backplane Bus":"Yes","PROFINET from GSD version/GSD revision":"GSDML V2.35","Monitoring of the supply voltage (PWR-LED)":"Yes; green PWR LED","Performance level according to ISO 13849-1":"PLe","Installation altitude above sea level, max.":"4 000 m; restrictions for installation altitudes > 2 000 m, see ET 200SP system manual","STEP 7 configurable/integrated from version":"as 6ES7136-6BA00-0CA0","power supply according to NEC Class 2 required":"No","Low demand mode: PFDavg in accordance with SIL3":"< 2.00E-05","STEP 7 TIA Portal configurable/integrated from version":"SIMATIC Safety V17 with HSP 0360 or higher","High demand/continuous mode: PFH in accordance with SIL3":"< 1.00E-09 1/h","Color code for module-specific color identification plate":"CC01","Between The Channels And The Power Supply Of The Electronics":"No"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$149.86 – $443.85","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/7e246528b6deb4f7e6adca52cef52d0f.pdf","sourceUrl":"https://support.industry.siemens.com/webbackend/api/ProductSupport/TechnicalData?language=en&region=cn&productId=1535487&mlfb=6ES7136-6BA01-0CA0"},"ai":{"faq":[{"question":"Is 6ES7136-6BA01-0CA0 compatible with existing ET 200SP systems?","answer":"Yes — it mounts on a BU type A0 BaseUnit and occupies one 15 mm slot in any ET 200SP station. The process image is 7 input bytes (6 bytes with S7-300/400F CPU) and 5 output bytes (4 bytes with S7-300/400F CPU)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/siemens/6ES7136-6BA01-0CA0","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/siemens/6ES7136-6BA01-0CA0 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}