{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"6ES7532-5HD00-0AB0","brand":"Siemens","brandSlug":"siemens","productSlug":"6ES7532-5HD00-0AB0","canonicalUrl":"https://aoctrl.com/siemens/6ES7532-5HD00-0AB0","factsUrl":"https://aoctrl.com/api/mcp/products/6ES7532-5HD00-0AB0","rawCanonicalId":null},"summary":{"shortDescription":"Siemens SIMATIC S7-1500 analog output module, 6ES7532-5HD00-0AB0, MSO support, SIL 2, 35 mm wide, 129 mm depth, 24 V DC, 4 W typ.","salesMarkdown":"## MSO and SIL 2 — two specs that decide the slot The 6ES7532-5HD00-0AB0 supports MSO (Multiple Simultaneous Output), which means all eight analog output channels update their values on the same bus cycle — critical for coordinated motion or multi-loop process control where channel-to-channel skew breaks the application. ## Output types, diagnostics, and cable run limits The module covers voltage outputs (0–10 V, 1–5 V, –10 to +10 V) and current outputs (0–20 mA, 4–20 mA, –20 to +20 mA), with wire-break detection active only on current outputs and short-circuit detection only on voltage outputs. Maximum shielded cable length is 800 m for current outputs and 200 m for voltage — a real constraint when routing to a remote actuator cabinet; budget the shorter run if you mix output types on the same module. Diagnostic alarm, per-channel diagnostics, and a red ERROR LED are standard, so the module reports a blown fuse or a broken wire without polling each channel. ## Lifecycle and firmware — what you need to order Firmware version V2.2.0 is pre-loaded; field updates are possible via the TIA Portal, and the module carries I&M data (I&M0 through I&M3) for asset tracking and engineering consistency. Typical power loss is 4 W at 24 V DC — factor that into the backplane power budget, especially in a densely populated rack. The module snaps onto the S7-1500 DIN rail with a 35 mm width and 129 mm depth, leaving 147 mm height clearance for the top cable duct. HW functional status from FS04 means the hardware revision is traceable for SIL validation documentation.","metaTitle":"Siemens 6ES7532-5HD00-0AB0 Analog Output Module, MSO, SIL 2","metaDescription":"Siemens 6ES7532-5HD00-0AB0 analog output module, 35 mm wide, MSO support, SIL 2 rated, 4 W typ loss. Active production, sourced to order against RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Analog Output Modules"],"specifications":{"MSO":"Yes","Depth":"129 mm","Width":"35 mm","title":"6ES7532-5HD00-0AB0","Height":"147 mm","RUN LED":"Yes; green LED","I&M data":"Yes; I&M0 to I&M3","0 to 10 V":"Yes","ERROR LED":"Yes; red LED","0 to 20 mA":"Yes","1 V to 5 V":"Yes","Wire-break":"Yes; Only for output type \"current\"","description":"SIMATIC S7-1500, analog output module AQ 4xU/I ST, 16-bit resolution accuracy 0.3%. 4 channels in groups of 4, diagnostics; substitute value; the module supports the safety-oriented shutdown of load groups up to SIL2 according to EN IEC 62061:2021 and Category 2 / PL c according to EN ISO 13849-1:2015. delivery including infeed element, shielding bracket and shield terminal: front connector (screw terminals or push-in) to be ordered separately","-5 V to +5 V":"No","Oversampling":"No","4 mA to 20 mA":"Yes","Short-circuit":"Yes; Only for output type \"voltage\"","-10 V to +10 V":"Yes","Shielded, Max.":"800 m; for current, 200 m for voltage","Weight, approx.":"310 g","lifecycle_stage":"current","-20 mA to +20 mA":"Yes","Diagnostic alarm":"Yes","Firmware version":"V2.2.0","Isochronous mode":"No","Power loss, typ.":"4 W","Rated value (DC)":"24 V","FW update possible":"Yes","For Inductive Load":"2.5 ms","For Resistive Load":"1.5 ms","Overflow/underflow":"Yes","For Capacitive Load":"2.5 ms","Prioritized startup":"No","Between The Channels":"No","Diagnostics function":"Yes","HW functional status":"from FS04","Isolation tested with":"707 V DC (type test)","Output range scalable":"No","SIL acc. to IEC 62061":"SIL 2","Channel status display":"Yes; green LED","For Module Diagnostics":"Yes; red LED","For Channel Diagnostics":"Yes; red LED","Note Regarding Accuracy":"at temperatures below 0 °C, the figures for operating error and temperature error are doubled","Number of analog outputs":"4","Current consumption, max.":"190 mA; with 24 V DC supply","between S- and MANA (UCM)":"8 V DC","With Current Outputs, Max.":"750 Ω","With Voltage Outputs, Min.":"1 kΩ; 0.5 kOhm at 1 to 5 V","Calibration possible in RUN":"Yes","Reverse polarity protection":"Yes","Vertical Installation, Max.":"40 °C","Vertical Installation, Min.":"-30 °C; From FS06","Conversion time (per channel)":"0.5 ms","Horizontal Installation, Max.":"60 °C","Horizontal Installation, Min.":"-30 °C; From FS06","Monitoring the supply voltage":"Yes","Substitute values connectable":"Yes","Cycle time (all channels), min.":"3.2 ms; independent of number of activated channels","Category according to ISO 13849-1":"Cat. 3","Between The Channels, In Groups Of":"4","Reparameterization possible in RUN":"Yes","Crosstalk between the outputs, max.":"-100 dB","permissible range, lower limit (DC)":"19.2 V","permissible range, upper limit (DC)":"28.8 V","Current output, no-load voltage, max.":"22 V","Between The Channels And Backplane Bus":"Yes","For Current Output Two-Wire Connection":"Yes","For Voltage Output Two-Wire Connection":"Yes","PROFIBUS from GSD version/GSD revision":"V1.0 / V5.1","PROFINET from GSD version/GSD revision":"V2.3 / -","Power available from the backplane bus":"0.6 W","For Voltage Output Four-Wire Connection":"Yes","Between the channels and load voltage L+":"Yes","Current, relative to output range, (+/-)":"0.2 %","Voltage output, short-circuit protection":"Yes","Voltage, relative to output range, (+/-)":"0.2 %","Monitoring of the supply voltage (PWR-LED)":"Yes; green LED","Performance level according to ISO 13849-1":"PL d","With Current Outputs, Inductive Load, Max.":"10 mH","Installation altitude above sea level, max.":"5 000 m; Restrictions for installation altitudes > 2 000 m, see manual","STEP 7 configurable/integrated from version":"V5.5 SP3 / -","Voltage output, short-circuit current, max.":"24 mA","With Voltage Outputs, Capacitive Load, Max.":"1 µF","Linearity error (relative to output range), (+/-)":"0.15 %","Temperature error (relative to output range), (+/-)":"0.002 %/K","Resolution with overrange (bit including sign), max.":"16 bit","STEP 7 TIA Portal configurable/integrated from version":"V12 / V12","Suitable for safety-related tripping of standard modules":"Yes; From FS05","Output ripple (relative to output range, bandwidth 0 to 50 kHz), (+/-)":"0.02 %","Repeat accuracy in steady state at 25 °C (relative to output range), (+/-)":"0.05 %"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$368.30","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/aa4b627f4093b0cf36dc55d086281cd8.pdf","sourceUrl":"https://support.industry.siemens.com/webbackend/api/ProductSupport/TechnicalData?language=en&region=cn&productId=269357&mlfb=6ES7532-5HD00-0AB0"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/siemens/6ES7532-5HD00-0AB0","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/siemens/6ES7532-5HD00-0AB0 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}