{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"6ES7532-5HF00-0AB0","brand":"Siemens","brandSlug":"siemens","productSlug":"6ES7532-5HF00-0AB0","canonicalUrl":"https://aoctrl.com/siemens/6ES7532-5HF00-0AB0","factsUrl":"https://aoctrl.com/api/mcp/products/6ES7532-5HF00-0AB0","rawCanonicalId":null},"summary":{"shortDescription":"Siemens SIMATIC S7-1500 analog output module, 35×147×129 mm, 24 V DC supply, firmware V2.1.0, SIL 2 per IEC 62061, order code 6ES7532-5HF00-0AB0.","salesMarkdown":"## Module identity and firmware baseline The Siemens 6ES7532-5HF00-0AB0 is an S7-1500 analog output module designed for the SIMATIC backplane, drawing 24 V DC on the supply rail and dissipating 7 W typical power loss. Firmware ships at V2.1.0 and the hardware functional status is recorded from FS01 upward, so any replacement slot must clear that FS line or the rack will reject the module on startup. MSO support is present, which lets the integrator keep multiple output slots time-synchronised for coordinated drive or valve commands across the cell. I&M data is supported from I&M0 through I&M3, which is the minimum set the maintenance planner needs for asset tagging and revision tracking when the module is rotated through the spares pool. Isochronous mode is enabled, which matters when the AO is closing a motion or closed-loop control loop on the same PROFIBUS/PROFINET cycle as the AI and CPU slices. ## Output ranges and load behaviour Wire-break detection is provided for the current output type, and short-circuit detection is provided for the voltage output type. Overflow and underflow diagnostics are flagged at the channel level alongside the diagnostic alarm raised on module faults, so a single 6ES7532-5HF00-0AB0 returns both wire-side and module-side faults to the HMI without an external relay per channel. Settling times are quoted per load class: 100 µs for inductive loads, 30 µs for resistive loads, and 100 µs for capacitive loads, each subject to the conditions given in the manual. ## Diagnostics, isolation, and field wiring Channel diagnostics raise a per-channel red LED, module diagnostics raise a separate red LED, and channel status shows green per channel with a green RUN LED at module level. ERROR LED indication is present at the module level. That LED split lets the field-service tech isolate a channel fault from a module fault without opening the cabinet door beyond the first swing-frame check. Isolation is type-tested at 707 V DC, which sets the clearance envelope the panel builder must preserve against adjacent power terminals. Shielded field cable is permitted to a maximum length of 200 m, which is the run-length ceiling for an analog loop fed from this module before a field repeater becomes mandatory. Output range scaling is not supported on this module, so the channel range is selected per channel from the supported list rather than rescaled in software. The rated supply is 24 V DC. Firmware updates are field-updatable, which is the path the maintenance buyer uses to pull V2.1.0 forward without a module swap.","metaTitle":"Siemens 6ES7532-5HF00-0AB0 AQ module, 8 AO, SIL 2","metaDescription":"Siemens 6ES7532-5HF00-0AB0 S7-1500 analog output module, 24 V DC, firmware V2.1.0, SIL 2 per IEC 62061. Lifecycle: current. RFQ-driven supply.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Analog Output Modules"],"specifications":{"MSO":"Yes","Depth":"129 mm","Width":"35 mm","title":"6ES7532-5HF00-0AB0","Height":"147 mm","RUN LED":"Yes; green LED","I&M data":"Yes; I&M0 to I&M3","0 to 10 V":"Yes","ERROR LED":"Yes; red LED","0 to 20 mA":"Yes","1 V to 5 V":"Yes","Wire-break":"Yes; Only for output type \"current\"","description":"SIMATIC S7-1500, analog output module AQ8xU/I HS, 16-bit resolution accuracy 0.3%, 8 channels in groups of 8, diagnostics; substitute value 8 channels in 0.125 ms oversampling; the module supports the safety-oriented shutdown of load groups up to SIL2 according to EN IEC 62061:2021 and Category 3 / PL d according to EN ISO 13849-1:2015. delivery including infeed element, shielding bracket and shield terminal: front connector (screw terminals or push-in) to be ordered separately","-5 V to +5 V":"No","Oversampling":"Yes","4 mA to 20 mA":"Yes","Short-circuit":"Yes; Only for output type \"voltage\"","-10 V to +10 V":"Yes","Shielded, Max.":"200 m","Weight, approx.":"325 g","lifecycle_stage":"current","-20 mA to +20 mA":"Yes","Diagnostic alarm":"Yes","Firmware version":"V2.1.0","Isochronous mode":"Yes","Power loss, typ.":"7 W","Rated value (DC)":"24 V","FW update possible":"Yes","For Inductive Load":"100 µs; see additional description in the manual","For Resistive Load":"30 µs; see additional description in the manual","Overflow/underflow":"Yes","For Capacitive Load":"100 µs; see additional description in the manual","Prioritized startup":"No","Between The Channels":"No","Diagnostics function":"Yes","HW functional status":"From FS01","Isolation tested with":"707 V DC (type test)","Output range scalable":"No","SIL acc. to IEC 62061":"SIL 2","Channel status display":"Yes; green LED","For Module Diagnostics":"Yes; red LED","For Channel Diagnostics":"Yes; red LED","Note Regarding Accuracy":"at temperatures below 0 °C, the figures for operating error and temperature error are doubled","Number of analog outputs":"8","Current consumption, max.":"320 mA; with 19.2 V supply","between S- and MANA (UCM)":"8 V DC","Bus cycle time (TDP), min.":"250 µs","With Current Outputs, Max.":"500 Ω","With Voltage Outputs, Min.":"1 kΩ","Calibration possible in RUN":"Yes","Reverse polarity protection":"Yes","Vertical Installation, Max.":"40 °C","Vertical Installation, Min.":"-30 °C; From FS03","Conversion time (per channel)":"50 µs; independent of number of activated channels","Horizontal Installation, Max.":"60 °C","Horizontal Installation, Min.":"-30 °C; From FS03","Monitoring the supply voltage":"Yes","Substitute values connectable":"Yes","Cycle time (all channels), min.":"125 µs; independent of number of activated channels","Category according to ISO 13849-1":"Cat. 3","Between The Channels, In Groups Of":"8","Reparameterization possible in RUN":"Yes","Crosstalk between the outputs, max.":"-100 dB","permissible range, lower limit (DC)":"19.2 V","permissible range, upper limit (DC)":"28.8 V","Current output, no-load voltage, max.":"20 V","Between The Channels And Backplane Bus":"Yes","For Current Output Two-Wire Connection":"Yes","For Voltage Output Two-Wire Connection":"Yes","PROFIBUS from GSD version/GSD revision":"V1.0 / V5.1","PROFINET from GSD version/GSD revision":"V2.3 / -","Power available from the backplane bus":"1.15 W","For Voltage Output Four-Wire Connection":"Yes","Between the channels and load voltage L+":"Yes","Current, relative to output range, (+/-)":"0.2 %","Voltage output, short-circuit protection":"Yes","Voltage, relative to output range, (+/-)":"0.2 %","Execution and activation time (TCO), min.":"100 µs","Monitoring of the supply voltage (PWR-LED)":"Yes; green LED","Performance level according to ISO 13849-1":"PL d","With Current Outputs, Inductive Load, Max.":"1 mH","Installation altitude above sea level, max.":"5 000 m; Restrictions for installation altitudes > 2 000 m, see manual","STEP 7 configurable/integrated from version":"V5.5 SP3 / -","Voltage output, short-circuit current, max.":"45 mA","With Voltage Outputs, Capacitive Load, Max.":"100 nF","Linearity error (relative to output range), (+/-)":"0.15 %","Temperature error (relative to output range), (+/-)":"0.002 %/K","Resolution with overrange (bit including sign), max.":"16 bit","STEP 7 TIA Portal configurable/integrated from version":"V14 / -","Suitable for safety-related tripping of standard modules":"Yes; from FS04","Output ripple (relative to output range, bandwidth 0 to 50 kHz), (+/-)":"0.02 %","Repeat accuracy in steady state at 25 °C (relative to output range), (+/-)":"0.05 %"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$546.10","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/28c7d7acde97e7f38a32dc2ad0e92d21.pdf","sourceUrl":"https://support.industry.siemens.com/webbackend/api/ProductSupport/TechnicalData?language=en&region=cn&productId=417294&mlfb=6ES7532-5HF00-0AB0"},"ai":{"faq":[{"question":"What is the listed MSO capability on this module?","answer":"MSO is listed as Yes, with isochronous mode supported, so the module participates in time-synchronised output across the S7-1500 backplane."},{"question":"What is the listed mechanical depth of 6ES7532-5HF00-0AB0?","answer":"The module depth is 129 mm, width 35 mm, height 147 mm, with an approximate mass of 325 g. The footprint matches a standard S7-1500 I/O slice, so it drops into an existing slot on mechanical grounds alone."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/siemens/6ES7532-5HF00-0AB0","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/siemens/6ES7532-5HF00-0AB0 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}