{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"BMI0703T16A","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"BMI0703T16A","canonicalUrl":"https://aoctrl.com/schneider/BMI0703T16A","factsUrl":"https://aoctrl.com/api/mcp/products/BMI0703T16A","rawCanonicalId":null},"summary":{"shortDescription":"Bosch Rexroth BMI servo motor, BMI0703T16A, single-phase, 700 W at 230 V, 3200 rpm, absolute single-turn Hiperface feedback, integrated EMC filter, keyed shaft, 300 mm length.","salesMarkdown":"## Feedback and signal integrity The BMI0703T16A: The absolute single-turn Hiperface SinCos encoder delivers position and speed data from power-up — no homing move needed, which shaves seconds off each cycle in pick-and-place or indexing stations. If you're commissioning this motor and see a drift or alarm on the drive, look at the shield termination first. The encoder cable shield should terminate at the drive end only; floating the motor side keeps ground loops off the SinCos lines. The integrated EMC filter clamps common-mode noise from the motor cable back to the drive. Mount the motor close to the drive cabinet — a long unshielded pigtail between the filter output and the motor defeats the attenuation. With the filter bonded to panel earth, conducted emissions stay inside the enclosure. ## Mounting and mechanical fit The motor flange is 70 mm square with a 60 mm centring collar and 5.5 mm mounting holes — mates to international standard flanges. Shaft is 14 mm diameter, keyed 5 mm wide, 30 mm long. Overall body length is 300 mm. Cooling is natural convection; no fan or forced air required. Leave at least 50 mm clearance around the housing for airflow. The IP54 shaft seal and IP65 housing tolerate washdown spray if the connector is properly torqued — but keep the cable entry pointed down to avoid pooling on the gland.","metaTitle":"Bosch Rexroth BMI0703T16A Servo Motor, Single-Phase, Hiperfa","metaDescription":"BMI0703T16A servo motor, 700 W, single-phase 230 V, SinCos Hiperface feedback, integrated EMC filter. Active production. Source via RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":[],"specifications":{"Phase":"Single phase","Length":"11.8 in (300 mm)","Category":"US1PC5618287","Key width":"0.2 in (5 mm)","Shaft end":"Keyed","EMC filter":"Integrated","Second shaft":"Without second shaft end","Shaft length":"1.2 in (30 mm)","Feedback type":"Absolute single turn SinCos Hiperface","Holding brake":"Without","Nominal speed":"3200 rpm 230 V single phase 1400 rpm 115 V single phase","Rotor inertia":"1.67 kg.cm²","Nominal torque":"25.7 lbf.in (2.9 N.m) 115 V single phase 19.5 lbf.in (2.2 N.m) 230 V single phase","Shaft diameter":"0.6 in (14 mm)","Torque constant":"0.81 N.m/A 68 °F (20 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Mounting Support":"International standard flange","Supply frequency":"50/60 Hz - 5...5 %","Back emf constant":"54.44 V/krpm 68 °F (20 °C)","Device short name":"BMI","Motor flange size":"2.8 in (70 mm)","Peak stall torque":"76.1 lbf.in (8.6 N.m) 115 V single phase 76.1 lbf.in (8.6 N.m) 230 V single phase","Stator inductance":"2.28 mH 68 °F (20 °C)","Stator resistance":"2.58 Ohm 68 °F (20 °C)","Maximum current Irms":"17.8 A 115 V, single phase 17.8 A 230 V, single phase","Nominal output power":"700 W 230 V single phase 400 W 115 V single phase","Centring collar depth":"0.10 in (2.5 mm)","Electrical Connection":"Printed circuit board connector","Nbr. of units in pkg.":"1","Number of motor poles":"10","Supply voltage limits":"100...240 V","Maximum axial force Fa":"0.2 x Fr","Number of motor stacks":"3","Output current 3s peak":"10.5 A 230 V 3 s","Continuous stall torque":"30.09 lbf.in (3.4 N.m) 115...230 V single phase","IP Degree of Protection":"Shaft IP54 Housing IP65","Maximum radial force Fr":"730 N 1000 rpm 580 N 2000 rpm 510 N 3000 rpm 460 N 4000 rpm 430 N 5000 rpm 400 N 6000 rpm","Mounting holes diameter":"0.2 in (5.5 mm)","Centring collar diameter":"2.4 in (60 mm)","Continuous stall current":"3.5 A","Maximum mechanical speed":"8000 rpm","Network frequency limits":"47.5...63 Hz","Number of mounting holes":"4","Continuous output current":"3.5 A 8 kHz","Product or Component Type":"Servo motor with power stage","Speed feedback resolution":"32768 points/turn","[Us] rated supply voltage":"115...230 V - 15...10 %","Distance shaft shoulder-flange":"0.10 in (2.5 mm)","Stator electrical time constant":"0.88 ms 68 °F (20 °C)","Circle diameter of the mounting holes":"3.0...3.2 in (75...82 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$1,315.00","priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/3ef5ce39c60629570259145cf22570e6.pdf","sourceUrl":null,"alternativesUrl":"https://aoctrl.com/api/mcp/products/BMI0703T16A/alternatives.json"},"ai":{"faq":[{"question":"What is the rated phase and voltage range?","answer":"It is a single-phase motor with supply voltage limits of 100...240 V and a frequency tolerance of 50/60 Hz ±5%."},{"question":"What is the body length and shaft diameter?","answer":"Length is 11.8 in (300 mm), shaft diameter is 0.6 in (14 mm), keyed with a 0.2 in (5 mm) key width and 1.2 in (30 mm) shaft length."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/BMI0703T16A","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/BMI0703T16A when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:21:01.794Z","lastPublished":"2026-09-02T08:21:01.794Z","indexable":true}}