{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILE2P661PC1A5","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILE2P661PC1A5","canonicalUrl":"https://aoctrl.com/schneider/ILE2P661PC1A5","factsUrl":"https://aoctrl.com/api/mcp/products/ILE2P661PC1A5","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric Lexium integrated drive, BLDC servo motor with 24:1 worm gear, 168 rpm at 3.8 Nm nominal torque, 18–55.2 V supply, 66 mm flange, ILE2P661PC1A5.","salesMarkdown":"## Form factor and mounting The ILE2P661PC1A5 ships as a 229 mm-long integrated motor-and-gearhead with a 66 mm flange face, designed for flange mounting directly to the driven load. The hollow output shaft on the gear side takes a pinned or clamped coupling — there's no second shaft end, so a single shaft seal layout covers the application. An industrial connector handles power, logic, and the four bidirectional signal lines, so cabinet-side wiring lands on a single plug rather than a separate driver. Natural convection cooling means no fan cut-out or air duct to derate in a sealed enclosure — the housing dissipates on its own at the 45 W / 66 W continuous output points. ## Gearing and torque envelope Two-stage worm gearing at a 24:1 reduction drops the brushless DC motor's medium-speed winding to a 168 rpm nominal output, both at 24 V and 48 V supply. The worm form gives a non-backdrivable output by default — useful for vertical-axis loads that must hold position when the drive is de-energised, at the cost of efficiency. Continuous torque is rated at 3.8 N·m at both 24 V and 48 V; peak stall torque reaches 6.19 N·m at the same supplies, and 45 W at 24 V or 66 W at 48 V of mechanical output is on the nameplate. Detent torque from the worm geometry is 2.9 N·m — this is the residual cogging the controller must overcome at zero speed, not the load capability. ## Feedback and control fidelity Position feedback comes from the integrated BLDC encoder, and the drive is specified at ±1 point of accuracy error — the resolution that matters for a 24:1 output shaft, not the raw motor-shaft count. The encoder is read inside the integrated drive, so the fieldbus layer just consumes the resolved position over the 100 Mbit link without an external counting module. Four signals are software-configurable as input or output, letting the same wiring handle end-of-travel limits, brake release, and a status output on installations where the I/O count is modest. Built-in protection covers output short circuit, output overload, and safe torque off — the STO function is the one that satisfies the safety circuit without an external contactor. ## Power, environment, and compliance The supply window is 18–55.2 V, which makes the unit suitable for both 24 VDC and 48 VDC bus architectures on machine skids. Peak current draw is 7 A with a 5.5 A maximum continuous figure — at 48 V that lines up with the 66 W continuous output, and the wiring gauge should be sized for the peak, not the continuous average. The drive carries a CE mark and is tested to EN/IEC 61800-3 second environment, EN/IEC 50178, and the IEC 60072-1 motor frame standard — the second-environment EMC classification means it can sit on the industrial floor of a plant without the filtering upgrades a first-environment (residential) install would need. Mechanical endurance is rated at 150 m/s² for shock across 1000 shocks and 20 m/s² sweep over 10 cycles on vibration; bearing service life is 3000 hours — that's the figure that defines the preventative replacement interval on a continuously-running conveyor or indexer. ## Procurement posture The unit ships one per package with an industrial connector, so panel build quantities are quoted to order against the BOM rather than pulled from a shelf.","metaTitle":"Schneider Electric ILE2P661PC1A5 servo drive, 3.8 Nm","metaDescription":"Schneider Electric ILE2P661PC1A5 Lexium integrated drive, 66 mm flange, 24:1 worm gearing, 18–55.2 V supply. Sourced to order against an RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors"],"specifications":{"Phase":"Single phase","title":"ILE2P661PC1A5","Length":"9.02 in (229 mm)","Marking":"CE","Category":"18288 - LEXIUM INTEGRATED DRIVES II","Shaft end":"Hole","Standards":"EN/IEC 61800-3 EN/IEC 50178 EN 61800-3:2001, second environment IEC 61800-3, Ed 2 EN 50347 EN 61800-3 : 2001-02 IEC 60072-1","Motor Type":"Brushless DC motor","description":"brushless dc motor 24..48 V - Ethernet Powerlink interface - L = 174 mm - 24:1","Network type":"DC","Second shaft":"Without second shaft end","Winding type":"Medium speed of rotation and medium torque","Detent torque":"25.7 lbf.in (2.9 N.m)","Feedback type":"BLDC encoder","Gear box type":"Worm gear, 2 stages","Holding brake":"Without","Nominal speed":"168 rpm 24 V 168 rpm 48 V","Rotor inertia":"90 kg.cm²","Accuracy error":"+/- 1 point","Nominal torque":"33.6 lbf.in (3.8 N.m) 24 V 33.6 lbf.in (3.8 N.m) 48 V","Protection Type":"Short circuit of the output voltage Overload of output voltage Safe torque off","Reduction ratio":"24:1 (525:22)","Type of cooling":"Natural convection","lifecycle_stage":"current","Mounting Support":"Flange","Range of Product":"Lexium integrated drive","Shock resistance":"150 m/s² 1000 shocks EN/IEC 60068-2-29","Device short name":"ILE","Input/output type":"4 signals (each be used as input or output)","Motor flange size":"2.6 in (66 mm)","Peak stall torque":"54.79 lbf.in (6.19 N.m) 24 V 54.79 lbf.in (6.19 N.m) 48 V","Relative humidity":"15...85 % without condensation","Transmission Rate":"100 Mbits","Operating altitude":"<= 3280.84 ft (1000 m) without derating","Current consumption":"7000 mA peak 5500 mA maximum continuous","Nominal output power":"45 W 24 V 66 W 48 V","Vibration resistance":"20 m/s² 10...500 Hz) 10 cycles EN/IEC 60068-2-6","Electrical Connection":"Industrial connector","Nbr. of units in pkg.":"1","Number of motor poles":"6","Service life in hours":"3000 h bearing","Supply voltage limits":"18...55.2 V","Associated fuse rating":"16 A","Discrete input current":"10 mA at 24 V on/STO_A safety input 3 mA at 24 V on/STO_B safety input 2 mA at 24 V 24 V signal interface","Maximum axial force Fa":"80 N","Maximum supply current":"0.1 A power stage disabled) 6.8 A 24 V 3.8 A 48 V","Number of motor stacks":"1","Commissioning interface":"RS485 Modbus TCP 9.6, 19.2 and 38.4 kbauds)","Communication interface":"Ethernet Powerlink, Integrated","Continuous stall torque":"37.2 lbf.in (4.2 N.m)","Discrete output voltage":"23...25 V","IP degree of protection":"IP41 shaft bushing: conforming to EN/IEC 60034-5 IP54 total except shaft bushing: conforming to EN/IEC 60034-5","Maximum radial force Fr":"200 N","Mounting holes diameter":"0.2 in (4.4 mm)","Centring collar diameter":"1.4 in (36 mm)","Maximum mechanical speed":"186 rpm","Number of mounting holes":"2","Maximum switching current":"100 mA per output 200 mA total","Product or Component Type":"Motion integrated drive","Speed feedback resolution":"12 points/turn motor 1.26° gearbox output","[Us] rated supply voltage":"48 V 24 V","Voltage state 0 guaranteed":"-3...4.5 V","Voltage state 1 guaranteed":"15...30 V","Ambient Air Temperature for Storage":"-13...158 °F (-25...70 °C)","Ambient air temperature for operation":"104...131 °F (40...55 °C) (with power derating of 2 % per °C) 32...104 °F (0...40 °C) (without derating)","Permissible ambient air temperature around the device":"221 °F (105 °C) power amplifier 230 °F (110 °C) motor"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/decdb8064a76fd33c53762f79b9e30dc.pdf","sourceUrl":"https://www.se.com/ie/en/product/ILE2P661PC1A5/brushless-dc-motor-24-48-v-ethernet-powerlink-interface-l-174-mm-241/"},"ai":{"faq":[{"question":"What is ILE2P661PC1A5's listed phase (Single phase) on this Servo Motors line?","answer":"The ILE2P661PC1A5 is listed as single phase with a DC network type — the unit is fed from a DC bus in the 18–55.2 V window, not from a multi-phase AC mains. The brushless DC motor windings are commutated internally by the integrated drive, so the field-side supply looks like a single DC feed to the cabinet designer."},{"question":"What is ILE2P661PC1A5's listed length (9.02 in (229 mm)) on this Servo Motors line?","answer":"Overall length is 9.02 in (229 mm) with a 66 mm motor flange. The 229 mm envelope includes the integrated worm gearhead, so a panel cut-out or machine frame clearance check should be done against the overall length rather than the motor body alone."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILE2P661PC1A5","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILE2P661PC1A5 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}