{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM0701P11F0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM0701P11F0000","canonicalUrl":"https://aoctrl.com/schneider/ILM0701P11F0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM0701P11F0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric, PacDrive 3 series, ILM servo motor integrated drive, 0.5 N.m nominal torque, 3 N.m holding brake, 70 mm flange, keyed shaft 11 mm.","salesMarkdown":"## PacDrive 3 ILM motor with the drive already inside The Schneider Electric ILM0701P11F0000 is a servo motor with an integrated drive from the PacDrive 3 family — the controller electronics are tucked into the back of a 70 mm flange servo, so a motion axis collapses into one mechanical package rather than separate drive cabinet + motor + cable run. Its ILM device short name and 70 mm flange carry the standard mounting interface used across the PacDrive 3 ILM series, which is the angle most retrofit jobs care about before the rest of the ratings matter. ## Torque envelope: 0.5 N.m working, 3 N.m parked Continuous stall torque is 1.1 N.m and nominal torque is 0.5 N.m, with a peak stall ceiling of 3.5 N.m — that three-to-one ratio between continuous and peak is what governs the dynamic headroom for short accel/decel moves in a packaging or pick-and-place axis. A holding brake rated 3 N.m comes fitted, sized to hold the same peak figure statically, so the motor parks locked without an external safety brake on a vertical or tilt axis. ## Speed, electrical constants and rotor inertia Nominal speed is 6000 rpm and continuous line current sits at 0.6 A — modest electrical demand, so the integrated drive does not need a separate cabinet feed beyond the PacDrive DC bus. Stator resistance is 10.4 Ohm phase-to-phase at 20 °C dropping to 7.23 Ohm phase-to-neutral at 120 °C, with 38.8 mH inductance (Ph/Ph) at 20 °C — useful numbers when sizing the drive loop bandwidth or predicting I²R heating in continuous-duty cycles. Nominal output power is 310 W, and the back-EMF constant is 46 V/krpm at 20 °C — the latter tells you roughly what DC bus the integrated drive is expecting for full speed without field weakening. ## Feedback and shaft interface Feedback is absolute single-turn SinCos Hiperface, which means absolute position survives a power cycle and the drive comes back up with axis coordinates already known — important on a retrofit where homing routines are a nuisance to re-run after every E-stop. The shaft is keyed with an 11 mm diameter, 23 mm length, 18 mm key width, and there is no second shaft end — the rear face is occupied by the drive electronics rather than a resolver pigtail or a second output for a gearbox. ## Bearing loads, sealing and cooling Maximum radial force Fr tapers from 660 N at 1000 rpm down to 360 N at 6000 rpm, with a maximum axial force Fa limited to 0.2 × Fr — the bearing budget erodes fast as speed rises, so a belt or pinion geometry that seems fine on paper at low speed can crowd the limit once the line ramps up. Cooling is natural convection rather than a forced-air fan, and the sealing is IP54 — which keeps the motor happy in a panel-internal or light-dust setting but rules out washdown food-and-bev cells unless the motor sits behind its own enclosure.","metaTitle":"Schneider Electric ILM0701P11F0000 PacDrive 3 servo motor","metaDescription":"Schneider Electric ILM0701P11F0000 PacDrive 3 ILM servo motor, integrated drive, 70 mm flange, 0.5 N.m nominal / 3 N.m holding. Quoted to order against an RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":[],"specifications":{"Length":"8.6 in (219 mm)","IP Rating":"IP54","Product Status":"Active","Shaft Diameter":"0.4 in (11 mm)","Shaft End Type":"Keyed","Max Axial Force Fa N":"0.2 x Fr","Centring Collar Diameter":"2.4 in (60 mm)","Main Product Or Component Type":"Servo motor integrated drive"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/a258996c1ae0982873691e7dead02ccd.pdf","sourceUrl":"https://www.se.com/ie/en/product/ILM0701P11F0000/ilm-integrated-drive-70mm-1-stack-keyed-shaft-sincos-singleturn-128-brake/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM0701P11F0000/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM0701P11F0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM0701P11F0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}