{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM0701P12F0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM0701P12F0000","canonicalUrl":"https://aoctrl.com/schneider/ILM0701P12F0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM0701P12F0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric PacDrive 3 ILM servo motor integrated drive, 0.5 N.m nominal torque, 3.5 N.m peak stall, 6000 rpm, 70 mm flange, IP54, keyed shaft.","salesMarkdown":"## PacDrive 3 ILM in one paragraph The ILM0701P12F0000: The Schneider Electric PacDrive 3 ILM servo motor integrated drive pairs a 0.5 N.m continuous-rated rotor with an integrated drive stage on a 70 mm flange, with 0.5 N.m nominal torque and a 3.5 N.m peak stall torque to absorb the inertial bursts of a sizing step without saturating the inverter (cites:,). 310 W of nominal output power at a 0.6 A line-rated current keeps the motor inside the natural-convection thermal envelope; forced-air assist is not specified because the housing relies on surface cooling alone (cites:,). ## Torque, current, and the headroom for sizing Continuous stall torque sits at 1.1 N.m against 0.5 N.m nominal at speed — the nominal-rating figure reflects what the rotor delivers in the operating envelope, while the continuous-stall ceiling is the absolute torque limit before thermal foldback (cites:,). Peak stall torque of 3.5 N.m is the short-duration margin the integrated drive can ask for during acceleration transients; sizing the mechanical system against peak rather than nominal avoids nuisance trips on every index move (cites:). Maximum Irms of 5.7 A versus a continuous 1.55 A stall current shows the same pattern: roughly 3.6× peak-to-continuous headroom for transient current demand (cites:,). Nominal speed of 6000 rpm is the published design point; the back-EMF constant of 46 V/krpm at 20 °C means the drive approaches its bus-voltage ceiling near top speed, which matters when the machine spends long stretches at rated rpm (cites:,). ## Mechanical fit and shaft loading The 70 mm flange, 60 mm centering collar with 2.5 mm depth, and four 5.5 mm mounting holes follow the IEC standard-flange pattern, so the motor drops into machine frames designed around the ILM family without adapter plates (cites:,). Overall length of 219 mm and a keyed 11 mm shaft with 23 mm engagement and 18 mm key width determine the pulley, pinion, or coupling selection — the key dimensions match the part drawing exactly (cites:,). Maximum radial force Fr drops from 660 N at 1000 rpm to 360 N at 6000 rpm, so a belt or gear train preloaded close to the low-speed limit will exceed the shaft-bearing envelope as the line ramps to top speed (cites:). Maximum axial Fa is constrained to 0.2 × Fr, the typical rule-of-thumb guard against preload from the driven load stacking axial force on the front bearing (cites:). ## Feedback, brake, and what ships in the box Absolute multiturn SinCos Hiperface feedback means the axis keeps its position reference through power cycles — no homing routine on every restart, which matters on a PacDrive 3 line where cycle-time loss is line-throughput loss (cites:). A holding brake is fitted and rated at 3 N.m holding torque, sized to park the axis in power-loss conditions rather than to brake a moving load — the brake envelope and the continuous-torque envelope are separate design limits (cites:,). Natural-convection cooling means no fan cable and no fan-failure mode; IP54 on the housing keeps the motor safe from dust ingress and water spray from any direction, but does not qualify it for direct washdown duty (cites:,). Six-pole rotor with one motor stack gives the inductance and resistance values that determine the current-loop bandwidth: 10.4 Ω phase-to-phase at 20 °C rises to 7.23 Ω phase-to-neutral at 120 °C, and stator inductance follows the same temperature dependency (cites:,).","metaTitle":"Schneider ILM0701P12F0000 PacDrive 3 ILM servo motor, 310 W","metaDescription":"Schneider ILM0701P12F0000 PacDrive 3 integrated-drive servo motor, 0.5 N.m nominal / 3.5 N.m peak, 6000 rpm, IP54. Sourced and quoted against an RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":[],"specifications":{"Length":"8.6 in (219 mm)","IP Rating":"IP54","Feedback Type":"Absolute multiturn SinCos Hiperface","Product Status":"Active","Shaft Diameter":"0.4 in (11 mm)","Shaft End Type":"Keyed","Max Axial Force Fa N":"0.2 x Fr","Max Radial Force Fr N":"660 N 1000 rpm 520 N 2000 rpm 460 N 3000 rpm 410 N 4000 rpm 380 N 5000 rpm 360 N 6000 rpm","Centring Collar Diameter":"2.4 in (60 mm)","Main Product Or Component Type":"Servo motor integrated drive"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/0c4d05c12e7cf9d60a571cdd8c14502b.pdf","sourceUrl":"https://www.se.com/ie/en/product/ILM0701P12F0000/ilm-integrated-drive-70mm-1-stack-keyed-shaft-sincos-multiturn-128-brake/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM0701P12F0000/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM0701P12F0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM0701P12F0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}