{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM0702P21F0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM0702P21F0000","canonicalUrl":"https://aoctrl.com/schneider/ILM0702P21F0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM0702P21F0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric, PacDrive 3, servo motor integrated drive, ILM0702P21F0000, 720 W, 1.15 N.m nominal, 6000 rpm, IP65.","salesMarkdown":"## Integrated drive motor in the PacDrive 3 ILM frame The Schneider Electric ILM0702P21F0000 is a servo motor with an integrated drive from the PacDrive 3 ILM family — a 70 mm flange, 252 mm-long unit that combines the motor and drive electronics in one housing rather than pairing a separate servo amplifier to a standalone motor. The 720 W nominal output and 1.15 N·m continuous torque sit at the low end of the ILM range, sized for compact packaging machines, small indexing tables, and feeder axes where a distributed drive cabinet adds more wiring than it saves. ## Torque, speed, and the 1.5 A / 11.8 A current envelope Continuous torque of 1.15 N·m against a 7.6 N·m peak stall gives roughly a 6.6× overload headroom — enough for short accel ramps without the drive tripping into I²T foldback, which matters for pick-and-place moves where the cycle time is dominated by the acceleration phase, not the steady-state run. Nominal speed is rated to 6000 rpm with a continuous line current of 1.5 A and a peak Irms of 11.8 A; the torque constant of 0.76 N·m/A at the 120 °C winding temperature lets the integrator back-calculate the current command needed for a given torque setpoint without trusting the default motor map. Back-EMF constant of 48 V/krpm at 20 °C and the 4.2 Ω phase-to-phase stator resistance at room temperature are the loop-tuning inputs — the drive uses them to model the electrical time constant, and any deviation in the measured winding resistance at install usually points to a cold-soak problem or a cable fault rather than a bad motor. ## Feedback, brake, and the Hiperface single-turn return Position feedback is a Hiperface SinCos single-turn absolute encoder — absolute to one turn, so the controller reads true shaft angle on power-up without a homing move, which removes one failure mode on vertical or unbalanced axes where a homing sequence after every E-stop would be unacceptable. The integrated holding brake is rated 3 N·m holding torque, sized to hold the rotor with the rated continuous torque applied at the shaft rather than to arrest a moving load — the brake is a parked-axis safety, not a dynamic stop, and any rapid-stop duty must come from the drive's regenerative or resistive path. ## IP65 sealing, natural convection, and where it mounts Cooling is natural convection — no fan, no blower path — and the housing carries an IP65 rating, meaning the unit survives low-pressure water jets and dust ingress and can sit on a machine frame near coolant splash or in a washdown-adjacent zone without an additional enclosure shroud, provided the cable glands and feedback connector are also sealed to the same rating. Mounting is the international standard flange pattern with a 60 mm centring collar, four 5.5 mm mounting holes, and a 70 mm flange square — the motor bolts directly to a standard gearhead or face-mount bracket without an adapter plate, and the 11 mm untapped shaft accepts a keyed coupling or pinion with a standard retaining method. Radial shaft load is derated against speed — 710 N at 1000 rpm stepping down to 390 N at 6000 rpm — with axial force capped at 0.2× the applied radial; a belt drive running near the top of the speed range must be tensioned conservatively, otherwise the bearing life curve on the nameplate starts to slip below the planned maintenance interval.","metaTitle":"Schneider Electric ILM0702P21F0000 Servo Motor, 720 W, IP65","metaDescription":"Schneider Electric PacDrive 3 ILM integrated servo motor, 720 W nominal, 1.15 N·m continuous, IP65. Quoted to order against the BOM.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":[],"specifications":{"Length":"9.9 in (252 mm)","IP Rating":"IP65","Product Status":"Active","Shaft Diameter":"0.4 in (11 mm)","Shaft End Type":"Untapped","Max Axial Force Fa N":"0.2 x Fr","Max Radial Force Fr N":"710 N 1000 rpm 560 N 2000 rpm 490 N 3000 rpm 450 N 4000 rpm 410 N 5000 rpm 390 N 6000 rpm","Centring Collar Diameter":"2.4 in (60 mm)","Main Product Or Component Type":"Servo motor integrated drive"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/5cde639d9083962577185e1fdbb83756.pdf","sourceUrl":"https://www.se.com/ie/en/product/ILM0702P21F0000/ilm-integrated-drive-70mm-2-stacks-smooth-shaft-ip65-sincos-singleturn-128-brake/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM0702P21F0000/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM0702P21F0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM0702P21F0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}