{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM0703P31A0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM0703P31A0000","canonicalUrl":"https://aoctrl.com/schneider/ILM0703P31A0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM0703P31A0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric, PacDrive 3 range, ILM series servo motor integrated drive, 720 W nominal output, 1.15 N·m nominal torque at 6000 rpm, keyed shaft, IP65, international standard flange mount.","salesMarkdown":"## Form factor the apprentice can put a tape on The ILM0703P31A0000 sits in the PacDrive 3 range as an ILM-series servo motor integrated drive with a 70 mm motor flange and a 259 mm body length, so the bench layout the junior sketches on the back of the panel drawing matches the actual footprint the motor drops into. Four 5.5 mm mounting holes on an international standard flange with a 60 mm centring collar at 2.5 mm depth lock the motor to the machine sub-plate — bring these dimensions to the mechanical side before the wiring day, not after. ## Operating envelope: 720 W with headroom for accelerations Continuous rating is 720 W at 6000 rpm nominal speed, with 1.15 N·m of nominal torque and 1.5 A line current; the peak stall torque of 8.7 N·m and maximum Irms of 12 A give the integrator the dynamic headroom to accelerate inertial loads without leaving the continuous envelope during steady-state. Continuous stall torque sits at 2.2 N·m at 3 A, so the holding figure under stationary load is roughly twice the running figure — that gap is what the motion controller reads as available torque margin during a move profile. ## Feedback, electrical constants, and the rotor the drive has to tame Position feedback is an absolute single-turn SinCos Hiperface device at 128 periods of resolution, so the PacDrive 3 controller gets absolute position on power-up without a homing move — useful on a line where the apprentice has to recommission after a power dip without re-zeroing every axis. Stator winding drops from 13 mH phase-to-phase at 20 °C to a lower phase-to-neutral figure at 120 °C, and resistance falls from 2.7 Ω to 1.88 Ω over the same span — the drive's current loop will see a warmer, lower-impedance motor at operating temperature than at cold start. ## Mechanical limits at the shaft The keyed shaft is 14 mm diameter by 30 mm long with a 20 mm key width and no second shaft end, so any side-mounted accessory (encoder stub, hand crank, tach) is off the table on this build — spec the gearbox or coupling to take everything off the drive end. Maximum radial force Fr drops from 730 N at 1000 rpm to 400 N at 6000 rpm — a belt or pinion mounted off the shoulder must be derated as speed climbs, not held at the low-speed figure, or the bearing budget silently disappears. Axial load is capped at 0.2 × Fr, and there is no holding brake on the motor — if the application needs to hold position with the bus off, the brake belongs on the gearbox or on a downstream mechanism, not on this part number. ## Sealing and cooling for the floor, not the bench Cooling is natural convection with no integrated fan, and the enclosure rating is IP65 — the motor can sit next to a washdown station or in a dusty cabinet without an air supply, but the installer still has to keep the cable glands torqued and the shaft seal clean, because IP65 is about the as-installed assembly, not just the motor body.","metaTitle":"Schneider Electric ILM0703P31A0000 PacDrive 3 servo motor","metaDescription":"Schneider Electric ILM0703P31A0000 PacDrive 3 integrated servo motor, 720 W nominal output, 1.15 N·m nominal torque, IP65, available to order against an RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Drives"],"specifications":{"Length":"10.2 in (259 mm)","Category":"US1PC5218351","Key width":"0.8 in (20 mm)","Shaft end":"Keyed","Second shaft":"Without second shaft end","Shaft length":"1.2 in (30 mm)","Feedback type":"Absolute single turn SinCos Hiperface","Holding brake":"Without","Nominal speed":"6000 rpm","Rotor inertia":"0.58 kg.cm²","Nominal torque":"10.18 lbf.in (1.15 N.m)","Shaft diameter":"0.6 in (14 mm)","Torque constant":"0.76 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Mounting Support":"International standard flange","Range of Product":"PacDrive 3","Back emf constant":"49 V/krpm 68 °F (20 °C)","Device short name":"ILM","Motor flange size":"2.8 in (70 mm)","Peak stall torque":"77.001 lbf.in (8.7 N.m)","Stator inductance":"13 mH 68 °F (20 °C) Ph/Ph 6.5 mH 248 °F (120 °C) Ph/N","Stator resistance":"2.7 Ohm 68 °F (20 °C) Ph/Ph 1.88 Ohm 248 °F (120 °C) Ph/N","Line Rated Current":"1.5 A","Maximum current Irms":"12 A","Nominal Output Power":"720 W","Centring collar depth":"0.10 in (2.5 mm)","Nbr. of units in pkg.":"1","Number of motor poles":"6","Maximum axial force Fa":"0.2 x Fr","Number of motor stacks":"3","Continuous stall torque":"19.5 lbf.in (2.2 N.m)","IP Degree of Protection":"IP65","Maximum radial force Fr":"730 N 1000 rpm 580 N 2000 rpm 510 N 3000 rpm 460 N 4000 rpm 430 N 5000 rpm 400 N 6000 rpm","Mounting holes diameter":"0.2 in (5.5 mm)","Centring collar diameter":"2.4 in (60 mm)","Continuous stall current":"3 A","Number of mounting holes":"4","Product or Component Type":"Servo motor integrated drive","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"250...700 V","Circle diameter of the mounting holes":"3.2 in (82 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/4389682d750739a2742696cb242af0c9.pdf","sourceUrl":"https://www.se.com/us/en/product/ILM0703P31A0000/integrated-servo-motor-2-2-nm-6000-rpm-keyed-shaft-without-brake-ip65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM0703P31A0000/alternatives.json"},"ai":{"faq":[{"question":"What is the listed length of the ILM0703P31A0000?","answer":"The body length is 10.2 in (259 mm) on a 70 mm flange, so the mechanical layout can be drawn against a 259 mm motor envelope plus the gearbox or coupling stack that mounts on the keyed shaft end."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM0703P31A0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM0703P31A0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}