{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM1002P11F0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM1002P11F0000","canonicalUrl":"https://aoctrl.com/schneider/ILM1002P11F0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM1002P11F0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric PacDrive 3 ILM-series servo motor integrated drive, 910 W nominal, 100 mm flange, Hiperface single-turn SinCos feedback, keyed shaft with holding brake, IP54.","salesMarkdown":"## What the part is — and why PacDrive 3 is the lead The ILM1002P11F0000 is the short name ILM on a PacDrive 3 range servo motor integrated drive from Schneider Electric; the lifecycle stage reads current on the record, which is the only signal procurement gets on paper before an RFQ is opened. An integrated drive — motor plus drive electronics on a single shaft — removes the separate amplifier cabinet and the long motor cable that drags a radiated-emissions signature through the panel; the ILM line carries its own back-EMF and torque constants so the controller parameter set can be loaded without a separate motor ID step. ## Headline ratings — power, torque, speed Nominal output is 910 W at 3000 rpm with a continuous stall torque of 4.4 N·m and a peak stall torque of 18.3 N·m — the roughly 4:1 peak-over-continuous headroom is the envelope inside which a PacDrive 3 motion profile can accelerate a packaging-line, pick-and-place, or short-stroke feed axis without saturating the current loop. Maximum current Irms is 13.1 A against a line-rated current of 2 A and a continuous stall current of 2.9 A — the Irms ceiling is the peak the drive will source for acceleration bursts while the continuous figures govern steady-state thermal sizing. ## Feedback, brake, and the electrical constants the controller needs Position feedback is absolute single-turn SinCos Hiperface — single-turn means absolute position within one revolution without battery backup, which suits rotary axes that do not need to retain absolute position across power cycles; Hiperface is the protocol the PacDrive 3 drive expects on commissioning. The holding brake provides 5.5 N·m of holding torque — sized to hold the vertical axis in place with the motor de-energised, which is the fail-safe state machine builders usually design to on packaging and small-format handling axes. Stator resistance and inductance are given at both 20 °C and 120 °C; the temperature split lets the PacDrive commissioning tool place the current-loop gains with the cold figure first and the warm figure for thermal compensation — without both values the gain scheduler can drift a few percent across a warm-up shift. ## Mechanical fit into the machine International standard flange mounting on a 100 mm motor flange, keyed shaft at 19 mm diameter and 40 mm shaft length, with four 9 mm mounting holes and a 95 mm centring collar 3.5 mm deep — that geometry mates to the standard NEMA-derived footprint common on small-format packaging, labelling, and pick-and-place gearboxes, so a replacement on an existing axis drop-in is the usual path. Overall length is 280 mm with a 30 mm key width on the keyed shaft; the second-shaft end is not provided — relevant where a manual handwheel or auxiliary encoder is on the BOM, since this build does not accept it without a flange change. IP54 seals against dust and splashing water from any direction, so the motor is acceptable inside a machine cabinet and on a washdown-adjacent axis but not on a direct spray zone; natural convection cooling means no fan cut-out to wire and no dust draw-in through a fan grille. Maximum radial force drops from 990 N at 1000 rpm to 690 N at 3000 rpm and maximum axial force is limited to 0.2 × Fr — the radial curve is the one that decides whether the pulley or pinion can sit outboard or has to be moved inboard to stay under the load line on a high-speed axis. ## Sourcing posture for the BOM line Lifecycle stage reads current on the record — no second-source or official successor is cited on the file, so the part is sourced per RFQ through independent distribution channels and quoted against the BOM quantity rather than held on a shelf promise.","metaTitle":"Schneider Electric ILM1002P11F0000 ILM Servo Motor, 910 W","metaDescription":"Schneider Electric ILM1002P11F0000 ILM-series servo motor integrated drive, 910 W nominal, 100 mm flange, Hiperface feedback, holding brake.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":[],"specifications":{"Length":"11.02 in (280 mm)","IP Rating":"IP54","Product Status":"Active","Shaft Diameter":"0.7 in (19 mm)","Shaft End Type":"Keyed","Max Axial Force Fa N":"0.2 x Fr","Max Radial Force Fr N":"990 N 1000 rpm 790 N 2000 rpm 690 N 3000 rpm","Centring Collar Diameter":"3.7 in (95 mm)","Main Product Or Component Type":"Servo motor integrated drive"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/c02697f1d81f51fd51a27f263cb14755.pdf","sourceUrl":"https://www.se.com/ie/en/product/ILM1002P11F0000/ilm-integrated-drive-100mm-2-stacks-keyed-shaft-sincos-singleturn-128-brake/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM1002P11F0000/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM1002P11F0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM1002P11F0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}