{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM1003P12A0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM1003P12A0000","canonicalUrl":"https://aoctrl.com/schneider/ILM1003P12A0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM1003P12A0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric PacDrive 3 ILM series servo motor integrated drive, 3.5 N·m nominal / 28.3 N·m peak, 3000 rpm, 1100 W, Hiperface SinCos multiturn feedback, IP54, flange mount.","salesMarkdown":"## Where does a 3.5 N·m integrated-drive servo fit the PacDrive 3 line? The ILM1003P12A0000: The part is a servo motor integrated drive in the PacDrive 3 range, device short name ILM, sized for the 1100 W / 3.5 N·m continuous nominal point at 3000 rpm — that envelope sits in the lower-mid of the ILM family and is typically dropped into a packaging-machine axis, a small pick-and-place, or a labelling station where the drive electronics are mounted on the motor back to cut cabinet space and wiring. ## Torque envelope — what 3.5 / 28.3 N·m means on the bench Nominal torque is 31.0 lbf.in (3.5 N·m) with a continuous stall torque of 51.3 lbf.in (5.8 N·m), and the peak stall reaches 250.5 lbf.in (28.3 N·m) — roughly 8× nominal — so the motor absorbs acceleration bursts (indexing, clamp-and-cut moves) without oversizing the continuous rating; the torque constant of 1.61 N·m/A at 248 °F (120 °C) is what the drive uses to close the current loop. Maximum current Irms is 21.2 A against a line-rated 2.4 A and a continuous stall current of 3.6 A, so the inverter section must be rated for the Irms peak even though the thermal design point is the 3.6 A continuous figure — sizing the upstream DC bus and brake resistor to the peak, not the nominal, is what keeps fast stops from tripping DC-bus overvoltage. ## Shaft, feedback, and the options this build skips Mechanical envelope: 11.2 in (285 mm) length, 3.9 in (100 mm) flange, keyed shaft of 0.7 in (19 mm) × 1.6 in (40 mm), no second shaft end, no holding brake, 4 mounting holes on a 9 mm bolt circle with a 3.7 in (95 mm) centring collar set 0.1 in (3.5 mm) deep — this is the brake-less, single-shaft build used where an external brake or a back-up encoder is not required. Feedback is absolute multiturn SinCos Hiperface with 128 periods of speed feedback resolution, so position is retained across power cycles without a battery box — the drive reads absolute position on first enable, then closes the velocity loop on the SinCos signal at runtime. ## Mechanical load limits and what they do to machine sizing Maximum radial force Fr derates from 1050 N at 1000 rpm to 830 N at 2000 rpm and 730 N at 3000 rpm, and the maximum axial force Fa is 0.2 × Fr — these are the bearing-life limits the mechanical designer has to check against belt tension or pinion forces, not the drive’s electrical envelope; radial load drives bearing life, not motor heating. Stator resistance 2.6 Ohm Ph/Ph at 68 °F (20 °C) and inductance 15.6 mH Ph/Ph at the same point (7.8 mH Ph/N at 248 °F / 120 °C) are the constants the drive firmware uses to tune the current loop — the 20 °C / 120 °C split is what the controller uses to compensate for copper shifts as the motor warms into its rated operating band.","metaTitle":"Schneider ILM1003P12A0000 Servo Motor, 1100 W, PacDrive 3","metaDescription":"Schneider Electric ILM1003P12A0000 servo motor integrated drive, 1100 W nominal, 3.5 N·m nominal torque, PacDrive 3. Specs, fit, and RFQ channel.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":[],"specifications":{"Length":"11.2 in (285 mm)","IP Rating":"IP54","Feedback Type":"Absolute multiturn SinCos Hiperface","Product Status":"Active","Shaft Diameter":"0.7 in (19 mm)","Shaft End Type":"Keyed","Max Axial Force Fa N":"0.2 x Fr","Max Radial Force Fr N":"1050 N 1000 rpm 830 N 2000 rpm 730 N 3000 rpm","Centring Collar Diameter":"3.7 in (95 mm)","Main Product Or Component Type":"Servo motor integrated drive"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/6ae3742c056f24e1d5f4c1837675f5b3.pdf","sourceUrl":"https://www.se.com/be/en/product/ILM1003P12A0000/ilm-integrated-drive-100mm-3-stacks-keyed-shaft-sincos-multiturn-128-no-brake/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM1003P12A0000/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM1003P12A0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM1003P12A0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}