{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"ILM1003P21F0000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"ILM1003P21F0000","canonicalUrl":"https://aoctrl.com/schneider/ILM1003P21F0000","factsUrl":"https://aoctrl.com/api/mcp/products/ILM1003P21F0000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric PacDrive 3 ILM integrated-drive servo motor, 1100 W nominal output, 9 N.m holding brake, SinCos Hiperface single-turn feedback, IP65, flange-mount.","salesMarkdown":"## Where does the ILM1003P21F0000 land on a PacDrive 3 axis? The ILM1003P21F0000 is a Schneider Electric PacDrive 3 ILM servo motor with an integrated drive — a single-cable axis that pairs the power stage directly with the rotor rather than running a separate drive cabinet per axis. Stator feeding a 3.5 N.m continuous torque at 3,000 rpm nominal with a 28.3 N.m peak torque ceiling means the axis has roughly 8× overload headroom for acceleration transients and indexing moves before the drive current-limits. A 5.8 N.m continuous stall torque at 3.6 A continuous stall current sets the thermal-floor derating point — the curve above which cooling, not torque capacity, governs the duty cycle. With natural convection as the only cooling path, panel thermal planning matters; the ILM1003P21F0000 cannot be derated upward by adding a fan, only down by trimming the motion profile to keep I²R heating below the housing thermal rise. ## Shaft, flange, and the cabinet cut-out An international-standard 100 mm flange with four 9 mm mounting holes on the standard bolt circle and a 95 mm centering collar drives the panel cut-out. The 19 mm untapped shaft with a 40 mm length and 30 mm keyway is sized for direct coupling to a gearbox or pinion without an intermediate sleeve. A second shaft end is omitted, so a manual handwheel or absolute multi-turn backup cannot be added later without re-specifying the motor. Radial shaft load is rated 1,050 N at 1,000 rpm and drops to 730 N at 3,000 rpm — the right part of the derating curve a belt or pinion drive sits on, which is why the motor stack count and inertia matter when sizing the coupling. Axial load is bounded at 0.2 × Fr, a conservative figure that treats the bearing as radial-limited. IP65 sealing on the body keeps coolant, oil mist, and cutting chips out of the rotor cavity, so the ILM1003P21F0000 can sit close to the process — typical PacDrive deployments push these onto machine frames rather than into a control cabinet. ## Feedback, brake, and electrical constants Absolute single-turn SinCos Hiperface feedback resolves position within one mechanical revolution and reports it back to the PacDrive controller through the Hiperface protocol — the loop bandwidth ceiling is set by this interface and the controller's sample time, not the motor itself. The integrated 9 N.m holding brake is a fail-safe parking brake sized to hold the rotor with the rated load; it is not a dynamic stopping brake for emergency stops. Back-EMF constant of 103 V/krpm at 20 °C and a torque constant of 1.61 N.m/A at 120 °C wound temperature gives the commissioning engineer the open-loop figures for sizing the DC-bus ramp and the current loop gains. Stator winding resistance measures 2.6 Ohm phase-to-phase at 20 °C and drops to 1.81 Ohm phase-to-neutral once warm — the inductance figure splits the same way across temperature, so the drive's auto-tune should be run at the expected operating temperature, not cold. ## Lifecycle and how to source it Lifecycle stage is recorded as current. The part is specified against the PacDrive 3 controller family, not the legacy PacDrive 2 or third-party servo buses, so any cross-reference must keep the same controller side intact to avoid a commissioning rework.","metaTitle":"Schneider ILM1003P21F0000 servo motor, 1100 W, IP65","metaDescription":"Schneider Electric ILM1003P21F0000 PacDrive 3 integrated-drive servo motor, 1100 W nominal, 9 N.m holding brake, SinCos Hiperface feedback, IP65.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":[],"specifications":{"Length":"12.4 in (315 mm)","IP Rating":"IP65","Product Status":"Active","Shaft Diameter":"0.7 in (19 mm)","Shaft End Type":"Untapped","Max Axial Force Fa N":"0.2 x Fr","Max Radial Force Fr N":"1050 N 1000 rpm 830 N 2000 rpm 730 N 3000 rpm","Centring Collar Diameter":"3.7 in (95 mm)","Main Product Or Component Type":"Servo motor integrated drive"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/eaf01c21c90bc32ca371c581522a73fb.pdf","sourceUrl":"https://www.se.com/ie/en/product/ILM1003P21F0000/ilm-integrated-drive-100mm-3-stacks-smooth-shaft-ip65-sincos-singleturn-128-brake/","alternativesUrl":"https://aoctrl.com/api/mcp/products/ILM1003P21F0000/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/ILM1003P21F0000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/ILM1003P21F0000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}