{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"LC1F2600G7","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"LC1F2600G7","canonicalUrl":"https://aoctrl.com/schneider/LC1F2600G7","factsUrl":"https://aoctrl.com/api/mcp/products/LC1F2600G7","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric TeSys F contactor, LC1F2600G7, 3-pole, 2600 A AC-1, 120 V AC 40-400 Hz coil, plate mount, end-of-life.","salesMarkdown":"The Schneider Electric LC1F2600G7 is a 3-pole TeSys F contactor rated for 2600 A in AC-1 duty (resistive loads), with a 120 V AC control coil operating at 40–400 Hz. It is designed for heavy switching of resistive loads such as large heating banks or furnace elements, where the AC-1 rating governs the continuous current-carrying capacity without derating for motor inrush. The contactor carries a full slate of international approvals: EN 60947-4-1, IEC 60947-4-1, UL 60947-4-1, CSA C22.2 No 60947-4-1, and JIS C8201-4-1, making it acceptable for panels destined for North America, Europe, and Asia without additional re-certification. The 2600 A AC-1 rating is the headline figure — it tells you the contactor can carry 2600 A continuously through resistive loads at up to 60 °C ambient. For motor loads (AC-3), the rating will be lower; this part is not sized for a motor starter without consulting the AC-3 derating curve. Short-time withstand current (Icw) is 12,000 A for 10 seconds at 40 °C, tapering to 4,000 A for 10 minutes. This matters for coordination with upstream protective devices — the contactor must be able to ride through a downstream fault until the breaker clears. The associated fuse recommendation is 2500 A gG at ≤ 440 V. Control circuit is AC only, 120 V at 40–400 Hz, with a pickup inrush of 2500 VA and a hold-in consumption of 45 VA. The coil dropout range is 0.3–0.5 Uc, so verify your control transformer sizing — the inrush can pull down a lightly loaded supply. Heat dissipation is 40 W total, with 250 W per pole in AC-1 service. That heat must be managed in the enclosure — plate mounting on a vertical surface with adequate airflow is assumed. The 0.1 mOhm average impedance at 2600 A 50 Hz gives a voltage drop of about 0.26 V per pole at full load. This is a plate-mount contactor — no DIN rail. The dimensions are substantial: 519 mm wide, 382 mm high, 251 mm deep. Power connections are via busbar, accepting up to 100 x 10 mm cross-section, with a tightening torque of 58 N.m. Control wiring uses screw clamp terminals accepting 1–4 mm² flexible or solid. The IP20 front face with shrouds is sufficient for enclosed panel use but not for washdown environments.","metaTitle":"Schneider Electric LC1F2600G7 TeSys F Contactor, 2600 A AC-1","metaDescription":"Schneider Electric LC1F2600G7 TeSys F contactor, 2600 A AC-1, 120 V AC coil. End-of-life (EOL) — sourced to order against RFQ. UL, CSA, IEC certified. Plate-mount, 3-pole.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Contactors"],"specifications":{"Depth":"251 mm","Range":"TeSys","Width":"519 mm","Height":"382 mm","Standards":"EN 60947-4-1 IEC 60947-1 IEC 60947-4-1 EN 60947-1 JIS C8201-4-1 UL 60947-4-1 CSA C22.2 No 60947-4-1","Operating time":"40...80 ms closing 100...200 ms opening","lifecycle_stage":"eol_hot","Heat dissipation":"40 W","Mounting support":"Plate","Range of product":"TeSys F","Average impedance":"0.1 mOhm - Ith 2600 A 50 Hz","Device short name":"LC1F","Poles description":"3P","Tightening torque":"Control circuit: 1.2 N.m Power circuit: 58 N.m","Compatibility code":"LC1F","Inrush power in VA":"2500 VA, 40...400 Hz cos phi 0.9 (at 20 °C)","Operating altitude":"3000 m without derating","Control circuit type":"AC at 40...400 Hz","Overvoltage category":"III","Protective treatment":"TH","Utilisation category":"AC-1","Contactor application":"Resistive load","Associated fuse rating":"2500 A gG at <= 440 V","Maximum operating rate":"600 cyc/h 55 °C","Connections - terminals":"Control circuit: screw clamp terminals 1 cable(s) 1...4 mm²flexible without cable end Control circuit: screw clamp terminals 2 cable(s) 1...4 mm²flexible without cable end Control circuit: screw clamp terminals 1 cable(s) 1...4 mm²flexible with cable end Control circuit: screw clamp terminals 2 cable(s) 1...2.5 mm²flexible with cable end Control circuit: screw clamp terminals 1 cable(s) 1...4 mm²solid without cable end Control circuit: screw clamp terminals 2 cable(s) 1...4 mm²solid without cable end Power circuit: bar 3 cable(s) - busbar cross section: 100 x 10 mm","IP degree of protection":"IP20 front face with shrouds conforming to IEC 60529 IP20 front face with shrouds conforming to VDE 0106","Rated breaking capacity":"3900 A conforming to IEC 60947-4-1","Product or component type":"Contactor","Power dissipation per pole":"250 W AC-1","[Uc] control circuit voltage":"120 V AC 40...400 Hz","[Ui] rated insulation voltage":"1000 V conforming to IEC 60947-4-1 1000 V conforming to UL 60947-4-1","Control circuit voltage limits":"Operational: 0.85...1.1 Uc 40...400 Hz (at 55 °C) Drop-out: 0.3...0.5 Uc 40...400 Hz (at 55 °C)","Power Pole Contact Composition":"3 NO","[Ie] rated operational current":"2600 A (at <60 °C) AC AC-1","[Ue] rated operational voltage":"<= 1000 V AC 50/60 Hz","Hold-in power consumption in VA":"45 VA, 40...400 Hz cos phi 0.9 (at 20 °C)","Ambient air temperature for storage":"-60...80 °C","Ambient air temperature for operation":"-5...40 °C","[Uimp] rated impulse withstand voltage":"8 kV","[Icw] rated short-time withstand current":"12000 A 40 °C - 10 s 9000 A 40 °C - 30 s 7000 A 40 °C - 1 min 6000 A 40 °C - 3 min 4000 A 40 °C - 10 min","[Ith] conventional free air thermal current":"2600 A (at 60 °C)","Permissible ambient air temperature around the device":"-40...60 °C"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/6498b91097927ae58675c3a46448652e.pdf","sourceUrl":"https://www.se.com/sg/en/product/LC1F2600G7/tesys-f-contactor-3p-3-no-ac1-1000-v-ac-2600-a-coil-120-v-ac/","alternativesUrl":"https://aoctrl.com/api/mcp/products/LC1F2600G7/alternatives.json"},"ai":{"faq":[{"question":"Where can I buy the LC1F2600G7 and get a price?","answer":"We source the LC1F2600G7 to order against an RFQ through our independent distribution network. Availability and current pricing are confirmed at quote time — submit an RFQ for a firm quote."},{"question":"What compliance documentation does Schneider provide for the LC1F2600G7?","answer":"The LC1F2600G7 carries approvals to EN 60947-4-1, IEC 60947-4-1, UL 60947-4-1, CSA C22.2 No 60947-4-1, and JIS C8201-4-1. These cover the major global regulatory frameworks for industrial control equipment."},{"question":"What is the LC1F2600G7's depth?","answer":"The depth is 251 mm."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/LC1F2600G7","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/LC1F2600G7 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}