{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"LC1F3304V7","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"LC1F3304V7","canonicalUrl":"https://aoctrl.com/schneider/LC1F3304V7","factsUrl":"https://aoctrl.com/api/mcp/products/LC1F3304V7","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric TeSys F, LC1F3304V7, 4-pole contactor, 400 A AC-1 rated, 400 V AC 50/60 Hz coil, plate mount, EOL phase-out.","salesMarkdown":"## TeSys F 4-pole contactor, 400 A AC-1 — LC1F3304V7 The Schneider Electric LC1F3304V7 is a TeSys F 4-pole contactor with a 400 V AC 50/60 Hz coil, rated for 400 A in AC-1 utilisation category (resistive load) at ≤ 440 V and ≤ 40 °C. It carries four normally open power poles and is plate-mounted — no DIN-rail clip, so factor in panel drilling and busbar work for the power circuit bolted connection or lugs up to 240 mm². Rated impulse withstand voltage is 8 kV (overvoltage category III), and insulation voltage is 1000 V per IEC 60947-4-1 or 1500 V per VDE 0110 group C. The contactor meets EN 60947-4-1, IEC 60947-4-1, and JIS C8201-4-1 — the usual suite for industrial switching gear. The 400 A AC-1 rating governs resistive loads like heaters or lighting banks. For motor duty (AC-3), you'd need to derate — this contactor is not specified for AC-3, so it is not the right choice for switching induction motors directly. The 4 NO pole configuration means all four poles close together; if your circuit needs any NC auxiliary, you'll add a separate block. Coil hold-in draws 10 VA at 400 V AC, with an inrush of 650 VA. The control circuit voltage limits are 0.85–1.1 Uc for pickup and 0.35–0.55 Uc for drop-out at 55 °C. Rated breaking capacity is 2640 A per IEC 60947-4-1, and the associated fuse recommendation is 400 A aM or 500 A gG at ≤ 440 V. That gives you a selectivity starting point for the upstream protection. The contactor is rated for 10 million mechanical cycles and can run at 2400 operations per hour at 55 °C — fine for high-duty-cycle resistive switching. Plate-mounted only — no DIN-rail adapter. The contactor measures 261 mm wide × 206 mm high × 219 mm deep. Power circuit connections accept lugs up to 240 mm² or busbar up to 30 × 5 mm via bolted connection. Control circuit uses screw clamp terminals accepting 1–4 mm² flexible or solid wire (with or without ferrule). Tightening torque: 1.2 N·m on control, 35 N·m on power. Protective treatment is TH (tropicalised) for humid environments.","metaTitle":"Schneider Electric LC1F3304V7 TeSys F Contactor, 400V AC Coi","metaDescription":"Schneider Electric LC1F3304V7 TeSys F contactor, 400V AC 50/60Hz coil, 4 NO poles, 400A AC-1 rated. EOL phase-out; sourced to order against RFQ. Quoted on request.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Contactors"],"specifications":{"Depth":"219 mm","Range":"TeSys","Width":"261 mm","Height":"206 mm","Standards":"EN 60947-4-1 EN 60947-1 JIS C8201-4-1 IEC 60947-1 IEC 60947-4-1","Operating time":"40...65 ms closing 100...170 ms opening","lifecycle_stage":"eol_hot","Heat dissipation":"8 W","Mounting support":"Plate","Range of product":"TeSys F","Average impedance":"0.28 mOhm - Ith 400 A 50 Hz","Device short name":"LC1F","Poles description":"4P","Tightening torque":"Control circuit: 1.2 N.m Power circuit: 35 N.m","Compatibility code":"LC1F","Inrush power in VA":"650 VA, 40...400 Hz cos phi 0.9 (at 20 °C)","Operating altitude":"3000 m without derating","Control circuit type":"AC at 40...400 Hz","Overvoltage category":"III","Protective treatment":"TH","Utilisation category":"AC-1","Contactor application":"Resistive load","Mechanical durability":"10 Mcycles","Associated fuse rating":"400 A aM at 500 A gG at <= 440 V","Maximum operating rate":"2400 cyc/h 55 °C","Connections - terminals":"Control circuit: screw clamp terminals 1 cable(s) 1...4 mm²flexible without cable end Control circuit: screw clamp terminals 2 cable(s) 1...4 mm²flexible without cable end Control circuit: screw clamp terminals 1 cable(s) 1...4 mm²flexible with cable end Control circuit: screw clamp terminals 2 cable(s) 1...2.5 mm²flexible with cable end Control circuit: screw clamp terminals 1 cable(s) 1...4 mm²solid without cable end Control circuit: screw clamp terminals 2 cable(s) 1...4 mm²solid without cable end Power circuit: lugs-ring terminals 1 cable(s) 240 mm² Power circuit: bar 2 cable(s) - busbar cross section: 30 x 5 mm Power circuit: bolted connection","IP degree of protection":"IP20 front face with shrouds conforming to IEC 60529 IP20 front face with shrouds conforming to VDE 0106","Rated breaking capacity":"2640 A conforming to IEC 60947-4-1","Product or component type":"Contactor","Power dissipation per pole":"44 W AC-1","[Uc] control circuit voltage":"400 V AC 40...400 Hz","[Ui] rated insulation voltage":"1000 V conforming to IEC 60947-4-1 1500 V conforming to VDE 0110 group C","Control circuit voltage limits":"Operational: 0.85...1.1 Uc 40...400 Hz (at 55 °C) Drop-out: 0.35...0.55 Uc 40...400 Hz (at 55 °C)","Power Pole Contact Composition":"4 NO","[Ie] rated operational current":"400 A (at <40 °C) at <= 440 V AC AC-1","[Ue] rated operational voltage":"<= 460 V DC","Hold-in power consumption in VA":"10 VA, 40...400 Hz cos phi 0.9 (at 20 °C)","Ambient air temperature for storage":"-60...80 °C","Ambient air temperature for operation":"-5...55 °C","[Uimp] rated impulse withstand voltage":"8 kV","[Icw] rated short-time withstand current":"2650 A 40 °C - 10 s 1800 A 40 °C - 30 s 1300 A 40 °C - 1 min 900 A 40 °C - 3 min 750 A 40 °C - 10 min","[Ith] conventional free air thermal current":"400 A (at 40 °C)","Permissible ambient air temperature around the device":"-40...70 °C"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/264cfba08d505b7ede8cbd17af1aeaac.pdf","sourceUrl":"https://www.se.com/nl/en/product/LC1F3304V7/tesys-f-contactor-4p-4-no-ac1-440-v-400-a-coil-400-v-ac/","alternativesUrl":"https://aoctrl.com/api/mcp/products/LC1F3304V7/alternatives.json"},"ai":{"faq":[{"question":"Where can I buy LC1F3304V7 and what is the lead time?","answer":"The LC1F3304V7 is sourced to order against an RFQ through independent distribution. Availability and current pricing are confirmed at quote time — no stock count or lead-time number is published here because the channel picture changes weekly on an EOL part."},{"question":"What is LC1F3304V7's rated operational current?","answer":"The LC1F3304V7 is rated for 400 A in AC-1 utilisation category (resistive load) at ≤ 440 V and ≤ 40 °C."},{"question":"What compliance documentation does Schneider provide for LC1F3304V7?","answer":"The contactor meets EN 60947-4-1, IEC 60947-4-1, JIS C8201-4-1, and IEC 60947-1. Rated insulation voltage is 1000 V per IEC 60947-4-1 or 1500 V per VDE 0110 group C. Impulse withstand voltage is 8 kV (overvoltage category III)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/LC1F3304V7","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/LC1F3304V7 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}