{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"MH30702P16F2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"MH30702P16F2200","canonicalUrl":"https://aoctrl.com/schneider/MH30702P16F2200","factsUrl":"https://aoctrl.com/api/mcp/products/MH30702P16F2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric MH30702P16F2200, MH3 series servo motor with brake, 1380 W continuous power, 1250 rpm nominal speed, 2.48 N·m continuous stall torque, IP65, single-turn SinCos Hiperface encoder, 70 mm flange.","salesMarkdown":"## Torque and speed profile for load matching The MH30702P16F2200: Rated 1380 W continuous power at 1250 rpm nominal speed, with a continuous stall torque of 2.48 N·m across the 115–480 V three-phase range — this is the holding torque the motor can sustain indefinitely without overheating, not the peak that clears a jam. Peak stall torque reaches 7.4 N·m at 115–480 V three-phase, giving a 3:1 torque overload margin for acceleration transients or short-duration overload events common in indexing and pick-and-place cycles. Nominal torque varies with supply voltage: 2.37 N·m at 115 V three-phase, 2.23 N·m at 230 V single-phase, 2.01 N·m at 400 V three-phase, and 1.89 N·m at 480 V three-phase — the torque derating above 115 V reflects the drive's current limit, not the motor's thermal capability. ## Encoder, brake, and environmental sealing Single-turn SinCos Hiperface encoder provides absolute position within one revolution — no homing sequence needed on power-up for rotary applications, but multi-turn position is lost if the drive loses power and the motor rotates. Integrated holding brake rated 3 N·m holding torque, with 7 W pull-in power — the brake engages when power is removed, holding the load on a vertical axis or during an E-stop; the 7 W coil power means a small 24 VDC supply can drive it without a separate brake rectifier. IP65 standard protection means the motor body is sealed against dust ingress and low-pressure water jets — suitable for washdown areas in food processing or machining coolant splash, but not for submersion or high-pressure spray (IP67 or IP69K would be needed for those). ## Mechanical fit and shaft interface 70 mm flange (IEC standard) with a 60 mm centring collar and 5.5 mm mounting holes — bolts directly to a standard NEMA 70 or IEC 70 frame mount without adapter plates. 11 mm shaft diameter with a parallel key, 23 mm shaft length, and 4 mm key width — the key transmits torque to the load coupling; the 0.2 in (4 mm) key width means the keyway in the mating hub must be broached to that width, not a standard 5 mm metric key. Maximum radial force at the shaft centre drops from 710 N at 1000 rpm to 390 N at 6000 rpm — belt-driven loads must be sized against the operating speed's force limit, not the static rating, to avoid bearing overload. ## Electrical parameters for drive tuning Stator resistance 3.84 Ω and inductance 12.19 mH give an electrical time constant of about 3.2 ms — the drive's current loop bandwidth must be set below the pole frequency to avoid oscillation; typical Lexium 52/62 drives auto-tune this on commissioning. Back EMF constant 54.08 V/krpm means the motor generates 54 V phase-to-phase for every 1000 rpm of mechanical speed — at 1250 rpm nominal, the back EMF is about 67.6 V, leaving headroom for the drive's bus voltage to push current into the windings. Continuous stall current 2.94 A and maximum current 9.68 A — the drive's continuous current rating should match the 2.94 A stall current for thermal balance; the 9.68 A peak supports acceleration and deceleration transients within the drive's overload envelope.","metaTitle":"Schneider Electric MH30702P16F2200 Servo Motor with Brake","metaDescription":"Schneider Electric MH30702P16F2200 servo motor with brake, 1380 W continuous power, 1250 rpm nominal speed, 2.48 N·m continuous stall torque, IP65.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":[],"specifications":{"Length":"7.6 in (193 mm)","IP Rating":"IP65","Encoder Type":"Single turn SinCos Hiperface","Product Status":"Active","Shaft Diameter":"0.4 in (11 mm)","Shaft End Type":"Parallel key","Centring Collar Diameter":"2.4 in (60 mm)","Main Product Or Component Type":"Servo motor"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/92220008f0974e161610cfab6414b3cd.pdf","sourceUrl":"https://www.se.com/be/en/product/MH30702P16F2200/mh3-servomotor-70mm-2-stacks-keyed-shaft-sincos-singleturn-16-brake-angular-ip65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/MH30702P16F2200/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/MH30702P16F2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/MH30702P16F2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}