{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"MH30702P17A2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"MH30702P17A2200","canonicalUrl":"https://aoctrl.com/schneider/MH30702P17A2200","factsUrl":"https://aoctrl.com/api/mcp/products/MH30702P17A2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric MH30702P17A2200 servo motor, three-phase, 1380 W continuous power, 5500 rpm nominal speed, 2.37 N.m nominal torque, Multiturn SinCos Hiperface encoder, IP65, without brake.","salesMarkdown":"The MH30702P17A2200 delivers 1380 W continuous power at 5500 rpm nominal speed — this is the sustained output for constant-velocity moves like conveyors or spindles. The nominal torque at the shaft is 2.37 N.m when paired with an LXM52 drive at 115 V three-phase, derating to 1.89 N.m at 480 V three-phase. For short-duration acceleration, the peak stall torque reaches 7.4 N.m at 115-480 V three-phase, but the continuous stall torque is 2.48 N.m — the thermal limit for holding or low-speed positioning. The torque constant of 0.84 N.m/A at 120 °C lets you convert drive current setpoints directly to shaft torque for tuning the current loop. Back EMF is 54.08 V/krpm — at 5500 rpm the motor generates 297 V line-to-line, so the drive's DC bus must stay above that to maintain current control. Stator inductance is 12.19 mH and resistance 3.84 Ohm, giving an electrical time constant of about 3.2 ms — the current loop bandwidth should be set below 300 Hz to avoid instability. ## Encoder feedback and mechanical interface The Multiturn SinCos Hiperface encoder provides absolute position feedback over 4096 revolutions — no homing cycle is needed after a power cycle, which saves time on multi-axis machines. The encoder signals are analog sine/cosine with a digital commutation track, so the drive can interpolate position to sub-micron resolution. The connector uses rotatable right-angled connectors for flexible cable routing in tight cabinets. The shaft is 11 mm diameter with a parallel key, 23 mm shaft length, and a 4 mm key width. The motor flange is 70 mm with a 60 mm centring collar and 2.5 mm collar depth — this matches standard IEC 71 frame dimensions, so it bolts directly to common gearboxes and linear actuators without adapters. Maximum radial force at the shaft is 710 N at 1000 rpm, derating to 390 N at 6000 rpm — factor this into bearing life calculations for belt-driven loads. ## IP65 and cooling — where it runs The motor carries IP65 protection — sealed against dust ingress and water jets from any direction. This suits washdown environments in food processing, packaging, or machining centres where coolant spray is present. Cooling is natural convection — no fan, so the motor relies on heat dissipation through the housing and mounting flange. In a confined cabinet or at continuous full load, expect surface temperatures up to 135 °C copper hot; ensure clearance for airflow and consider a thermal break if mounting to heat-sensitive components.","metaTitle":"Schneider Electric MH30702P17A2200 Servo Motor, 1380 W","metaDescription":"Schneider Electric MH30702P17A2200 servo motor, three-phase, 1380 W continuous power, 5500 rpm nominal speed, IP65, Multiturn SinCos Hiperface encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"MH30702P17A2200","Length":"6.06 in (154 mm)","Inertia":"0.0 kg.cm² of brake 1.13 kg.cm² of motor","Category":"US1PC5218359","Key width":"0.2 in (4 mm)","Shaft end":"Parallel key","description":"MH3 servomotor, 70mm, 2 stacks, keyed Shaft, SinCos Multiturn 16, no Brake, angular, IP65","Encoder type":"Multiturn SinCos Hiperface","Second shaft":"Without second shaft end","Shaft length":"0.9 in (23 mm)","Holding brake":"Without","Nominal speed":"5500 rpm","Rotor inertia":"1.13 kg.cm²","Nominal torque":"20.98 lbf.in (2.37 N.m) LXM52 2.82 mA, 115 V, three phase 19.74 lbf.in (2.23 N.m) LXM52 2.7 mA, 230 V, single phase 17.79 lbf.in (2.01 N.m) LXM52 2.49 mA, 400 V, three phase 16.73 lbf.in (1.89 N.m) LXM52 2.36 mA, 480 V, three phase 20.98 lbf.in (2.37 N.m) LXM62 2.82 mA, 115 V, single phase 19.74 lbf.in (2.23 N.m) LXM62 2.7 mA, 230 V, single phase 17.79 lbf.in (2.01 N.m) LXM62 2.49 mA, 400 V, three phase 16.73 lbf.in (1.89 N.m) LXM62 2.36 mA, 480 V, three phase","Shaft diameter":"0.4 in (11 mm)","Torque constant":"0.84 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"1380 W","Mounting Support":"International standard flange","Sizing reference":"MH30702P","Back emf constant":"54.08 V/krpm","Device short name":"MH3","Motor flange size":"2.8 in (70 mm)","Peak stall torque":"65.5 lbf.in (7.4 N.m), 115...480 V, three phase","Stator inductance":"12.19 mH","Stator resistance":"3.84 Ohm","Maximum current Irms":"9.65 A","Nominal output power":"0.31 W, 115 V 0.7 W, 230 V 1.16 W, 400 V 1.38 W, 480 V","Centring collar depth":"0.10 in (2.5 mm)","Electrical Connection":"Rotatable right-angled connectors","Nbr. of units in pkg.":"1","Number of motor poles":"5.0","Output current 3s peak":"9.65 A","Temperature copper hot":"275 °F (135 °C)","Continuous stall torque":"21.95 lbf.in (2.48 N.m), 115...480 V, three phase","IP Degree of Protection":"IP65 standard","Maximum radial force Fr":"710 N 1000 rpm 560 N 2000 rpm 490 N 3000 rpm 450 N 4000 rpm 410 N 5000 rpm 390 N 6000 rpm","Mounting holes diameter":"0.2 in (5.5 mm)","Centring collar diameter":"2.4 in (60 mm)","Continuous stall current":"2.94 A","Maximum mechanical speed":"8000 rpm","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"16 periods","[Us] rated supply voltage":"115...480 V","Stator electrical time constant":"3.2 ms","Circle diameter of the mounting holes":"3.2 in (82 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/b873a79a7969631659140168a2bf9b48.pdf","sourceUrl":"https://www.se.com/us/en/product/MH30702P17A2200/mh3-servomotor-70mm-2-stacks-keyed-shaft-sincos-multiturn-16-no-brake-angular-ip65/"},"ai":{"faq":[{"question":"What encoder type does the MH30702P17A2200 use?","answer":"It uses a Multiturn SinCos Hiperface encoder providing absolute position feedback over 4096 revolutions. This eliminates the need for a homing cycle on power-up, saving time on multi-axis machines."},{"question":"Does the MH30702P17A2200 include a holding brake?","answer":"No, this variant ships without a holding brake. For vertical-axis applications, an external brake or counterbalance must be added to hold the load at zero speed without power."},{"question":"What is the IP rating of the MH30702P17A2200?","answer":"The motor carries IP65 protection — sealed against dust ingress and water jets from any direction, suitable for washdown environments in food processing or machining centres."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/MH30702P17A2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/MH30702P17A2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}