{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"MH31402P07F2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"MH31402P07F2200","canonicalUrl":"https://aoctrl.com/schneider/MH31402P07F2200","factsUrl":"https://aoctrl.com/api/mcp/products/MH31402P07F2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric MH31402P07F2200 MH3 series servo motor with brake, three phase, 3.73 kW continuous power at 400/480 V, 3000 rpm, 18.5 N.m continuous stall torque, IP65, Multiturn SinCos Hiperface encoder, smooth shaft, 140 mm flange.","salesMarkdown":"## 3.73 kW servo with holding brake for vertical-axis loads The MH31402P07F2200 is a three-phase servo motor from the Schneider Electric MH3 series, delivering 3.73 kW continuous power at 400/480 V supply. Nominal speed is 3000 rpm, with a continuous stall torque of 18.5 N.m across the 115...480 V range. Peak stall torque reaches 55.5 N.m for acceleration and deceleration transients, limited to the 3-second peak current rating of 46.22 A. ## Multiturn absolute encoder and IP65 sealing The Multiturn SinCos Hiperface encoder provides absolute position feedback over multiple shaft revolutions — no homing cycle needed after power loss. This is critical for applications like gantry robots or tool changers where position must be retained. IP65 standard protection means the motor body is sealed against dust ingress and low-pressure water jets from any direction. Suitable for washdown environments in food processing or machining coolant splash — but the connector must be properly mated to maintain the seal. Rotatable right-angled connectors allow the cable exit to be oriented in 90° increments, simplifying cable routing in tight cabinets or on moving axes. ## Torque and speed ratings across drive voltages Nominal torque varies with the drive voltage and type: 16.34 N.m with LXM52 at 115 V three-phase, 14.0 N.m with LXM52 at 230 V single-phase, and 10.17 N.m with LXM52 at 400 V or 480 V three-phase. The same pattern applies for LXM62 drives. The torque constant is 1.24 N.m/A at 120 °C copper temperature — use this to calculate the RMS current required for a given load torque profile. Back EMF constant is 70.7 V/krpm, which determines the DC bus voltage needed to reach rated speed. Stator resistance is 0.23 Ohm and inductance is 2.99 mH — these values feed into the drive's current loop tuning and I²R loss calculation for thermal modelling. ## Mechanical interface and mounting constraints The motor flange is 140 mm (5.5 in) with an international standard flange pattern — mounting holes at 11 mm diameter on a 130 mm centring collar. Centring collar depth is 3.5 mm. Smooth shaft (no keyway) with 24 mm diameter and 50 mm shaft length. A clamping-type coupling or shaft collar is required — set-screw couplings on a smooth shaft risk slipping under peak torque. Maximum radial force at the shaft end is 2240 N at 1000 rpm, derating to 1550 N at 3000 rpm. Exceeding these limits shortens bearing life — check the driven load's overhung force against the speed curve. Overall motor length is 227 mm (8.9 in) excluding the connector and cable bend radius. Natural convection cooling — no fan, so the motor relies on its own surface area and mounting plate for heat dissipation. ## Active production — sourcing and lifecycle Sourced through authorized distribution channels. No minimum order quantity restrictions beyond standard packaging (1 unit per package). No official successor or cross-reference part is recorded — this is the current production variant for the MH3 frame size at 3.73 kW with holding brake and Hiperface encoder.","metaTitle":"Schneider Electric MH31402P07F2200 Servo Motor with Brake","metaDescription":"Schneider Electric MH31402P07F2200 servo motor with brake, 3.73 kW continuous power at 400/480 V, 3000 rpm nominal speed, 18 N.m holding brake, IP65, Multiturn","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"MH31402P07F2200","Length":"8.9 in (227 mm)","Inertia":"1.5 kg.cm² of brake 32.0 kg.cm² of motor","Category":"US1PC5218359","Shaft end":"Smooth shaft","description":"MH3 servomotor, 140mm, 2 stacks, smooth Shaft, SinCos Multiturn 16, Brake, angular, IP65","Encoder type":"Multiturn SinCos Hiperface","Second shaft":"Without second shaft end","Shaft length":"2.0 in (50 mm)","Holding brake":"With","Nominal speed":"3000 rpm","Rotor inertia":"33.5 kg.cm²","Holding torque":"159.3 lbf.in (18 N.m)","Nominal torque":"144.62 lbf.in (16.34 N.m) LXM52 14.87 mA, 115 V, three phase 123.9 lbf.in (14.0 N.m) LXM52 13.13 mA, 230 V, single phase 90.01 lbf.in (10.17 N.m) LXM52 9.76 mA, 400 V, three phase 90.01 lbf.in (10.17 N.m) LXM52 9.76 mA, 480 V, three phase 144.62 lbf.in (16.34 N.m) LXM62 14.87 mA, 115 V, single phase 123.9 lbf.in (14.0 N.m) LXM62 13.13 mA, 230 V, single phase 90.01 lbf.in (10.17 N.m) LXM62 9.76 mA, 400 V, three phase 90.01 lbf.in (10.17 N.m) LXM62 9.76 mA, 480 V, three phase","Shaft diameter":"0.9 in (24 mm)","Torque constant":"1.24 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"3730 W","Mounting Support":"International standard flange","Sizing reference":"MH31402P","Back emf constant":"70.7 V/krpm","Device short name":"MH3","Motor flange size":"5.5 in (140 mm)","Peak stall torque":"491.2 lbf.in (55.5 N.m), 115...480 V, three phase","Stator inductance":"2.99 mH","Stator resistance":"0.23 Ohm","Brake pull-in power":"18 W","Maximum current Irms":"46.22 A","Nominal output power":"1.71 W, 115 V 2.93 W, 230 V 3.73 W, 400 V 3.73 W, 480 V","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Rotatable right-angled connectors","Nbr. of units in pkg.":"1","Number of motor poles":"5.0","Output current 3s peak":"46.22 A","Temperature copper hot":"275 °F (135 °C)","Continuous stall torque":"163.7 lbf.in (18.5 N.m), 115...480 V, three phase","IP Degree of Protection":"IP65 standard","Maximum radial force Fr":"2240 N 1000 rpm 1780 N 2000 rpm 1550 N 3000 rpm","Mounting holes diameter":"0.4 in (11 mm)","Centring collar diameter":"5.1 in (130 mm)","Continuous stall current":"16.83 A","Maximum mechanical speed":"4000 rpm","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"16 periods","[Us] rated supply voltage":"115...480 V","Stator electrical time constant":"13 ms","Circle diameter of the mounting holes":"6.5 in (165 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/082fba36c1210e19b1b838d1b918eb6c.pdf","sourceUrl":"https://www.se.com/be/en/product/MH31402P07F2200/mh3-servomotor-140mm-2-stacks-smooth-shaft-sincos-multiturn-16-brake-angular-ip65/"},"ai":{"faq":[{"question":"What is the holding torque of the brake on the MH31402P07F2200?","answer":"The integrated holding brake provides 18 N.m (159.3 lbf.in) holding torque. Brake pull-in power is 18 W."},{"question":"What encoder type does the MH31402P07F2200 use?","answer":"It uses a Multiturn SinCos Hiperface encoder, providing absolute position feedback over multiple shaft revolutions without requiring a homing cycle after power loss."},{"question":"What is the IP rating of the MH31402P07F2200?","answer":"IP65 standard protection — dust-tight and protected against low-pressure water jets from any direction. Suitable for washdown environments when connectors are properly mated."},{"question":"What is the shaft diameter and type on the MH31402P07F2200?","answer":"Smooth shaft (no keyway), 24 mm diameter, 50 mm shaft length. A clamping-type coupling is required — set-screw couplings risk slipping under peak torque."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/MH31402P07F2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/MH31402P07F2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}