{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH30553P0BF4100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH30553P0BF4100","canonicalUrl":"https://aoctrl.com/schneider/SH30553P0BF4100","factsUrl":"https://aoctrl.com/api/mcp/products/SH30553P0BF4100","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series AC servo motor with brake, SH30553P0BF4100, 680 W continuous, 9000 rpm maximum, IP65, Hiperface DSL absolute multiturn encoder.","salesMarkdown":"## Sizing the motor to the drive's torque and speed envelope The SH30553P0BF4100 sits in Schneider Electric's SH3 servo family and carries the SH30553P sizing reference, so an SH3-rated drive or Lexium servo drive from the same generation will accept it on the same feedback protocol and power chain. Continuous power is 680 W, with the same 680 W nominal output at both 400 V three phase and 480 V three phase, dropping to 390 W on 230 V single phase, which is the rail the drive cabinet has to deliver. Nominal torque scales with the supply: 1.1 N·m on 230 V single phase against 0.81 N·m on either 400 V or 480 V three phase. Peak stall torque reaches 3.5 N·m across the 115–480 V three-phase window, meaning the drive's current limit must be set above the 6.5 A Irms / 6.5 A 3 s peak rating to use that peak in the acceleration profile without saturating the controller. Maximum mechanical speed is 9000 rpm, reached on 480 V three phase. The 4000 rpm figure on 230 V single phase is the field-weakening ceiling on that supply, not a separate model variant — drives that push the speed command past the rail-limited speed will simply roll off torque per the motor's back-EMF constant of 41 V/krpm at 20 °C. ## Brake, feedback, and the wiring that lands on the cabinet The integrated holding brake delivers 0.8 N·m of holding torque with a 10 W pull-in coil, sized to lock a vertical or incline axis on power loss without oversizing the cabinet's 24 V brake supply. The encoder is an absolute multiturn Hiperface DSL unit, which means the single-cable quicklock rotatable right-angled connector carries both power and feedback back to the drive — count one cable, not two, in the panel gland plate layout. ## Mechanical envelope, sealing, and panel-side fit IP65 on both the motor body and the shaft bushing per IEC 60034-5 means the housing tolerates hose-down and dusty cell environments, but the rating applies to the mated connector, not the bare shaft — the through-bore at the cable entry is the wet-end barrier, so the sealing washer on the gland has to seat on install. Cooling is natural convection, so derating begins above the 130 °C copper-hot thermal limit; forced-air or a heatsink is not part of the catalogue configuration. ## Drive-matching constants for the commissioning engineer Torque constant is 0.62 N.m/A at 120 °C, paired with stator resistance 10.4 Ohm and stator inductance 13.02 mH — three figures that drop directly into the drive's current-loop tuning. Continuous stall torque is 1.05 N·m at 1.7 A continuous stall current, the figure that decides whether the motor holds a static load without tripping the drive's I²T thermal model. ## Lifecycle posture and how this part is quoted Sourcing runs through independent distribution against an RFQ — production quantities, lead time, and current pricing come back with the quote, and the order is filled against the BOM position rather than off the shelf.","metaTitle":"Schneider SH30553P0BF4100 SH3 servo motor, 680 W, IP65","metaDescription":"Schneider Electric SH30553P0BF4100 SH3 servo motor with brake: 680 W continuous, 1.1 N·m nominal torque, 9000 rpm max, IP65, Hiperface DSL.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"title":"SH30553P0BF4100","Length":"203 mm","Inertia":"0.021 kg.cm² of brake 0.134 kg.cm² of motor","Shaft end":"Smooth shaft","description":"SH3 servomotor, 55mm, 3 stacks, smooth Shaft, Multiturn DSL 18bit, Brake, OneMotorCable angular M17, IP65/65","Encoder type":"Absolute multiturn Hiperface DSL","Shaft length":"20 mm","Holding brake":"With","Nominal speed":"4000 rpm at 230 V single phase 8000 rpm at 400 V three phase 9000 rpm at 480 V three phase","Rotor inertia":"0.155 kg.cm²","Holding torque":"0.8 N.m","Nominal torque":"1.1 N.m at 230 V single phase 0.81 N.m at 400 V three phase 0.81 N.m at 480 V three phase","Product weight":"1.95 kg","Shaft diameter":"9 mm","Torque constant":"0.62 N.m/A at 120 °C","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"680 W","Mounting support":"International standard flange","Sizing reference":"SH30553P","Back emf constant":"41 V/krpm at 20 °C","Device short name":"SH3","Motor flange size":"55 mm","Peak stall torque":"3.5 N.m at 115...480 V three phase","Stator inductance":"13.02 mH","Stator resistance":"10.4 Ohm","Brake pull-in power":"10 W","Maximum current Irms":"6.5 A","Nominal output power":"390 W at 230 V single phase 680 W at 400 V three phase 680 W at 480 V three phase","Centring collar depth":"2 mm","Electrical connection":"quicklock rotatable right angled connector","Number of motor poles":"3.0","Maximum axial force Fa":"80 N","Output current 3s peak":"6.5 A","Temperature copper hot":"130 °C","Continuous stall torque":"1.05 N.m at 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"710 N at 1000 rpm","Mounting holes diameter":"5.5 mm","Centring collar diameter":"40 mm","Continuous stall current":"1.7 A","Maximum mechanical speed":"9000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or component type":"Servo motor","Speed feedback resolution":"262144 points/turn x 4096 turns","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"63 mm"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/947a223206f7c1020dd9ba27f840cd0e.pdf","sourceUrl":"https://www.se.com/uk/en/product/SH30553P0BF4100/sh3-servomotor-55mm-3-stacks-smooth-shaft-multiturn-dsl-18bit-brake-onemotorcable-angular-m17-ip65-65/"},"ai":{"faq":[{"question":"What is the SH30553P0BF4100's listed length on this servo motor line?","answer":"Length is 203 mm, with a 55 mm flange and 1.95 kg product weight — a compact body that lands on a standard machine-builder slide without a custom bracket."},{"question":"What is the SH30553P0BF4100's listed inertia on this servo motor line?","answer":"Rotor inertia is 0.155 kg.cm², with the bare motor rated at 0.134 kg.cm² and the brake adding 0.021 kg.cm² on top. The figure is what the drive's auto-tuning routine reads to set the velocity-loop gain."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH30553P0BF4100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH30553P0BF4100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}