{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH30553P11F2100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH30553P11F2100","canonicalUrl":"https://aoctrl.com/schneider/SH30553P11F2100","factsUrl":"https://aoctrl.com/api/mcp/products/SH30553P11F2100","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor with brake, SH30553P11F2100, 680 W continuous power, 55 mm flange, IP65, absolute single-turn SinCos Hiperface encoder, 2000-6000 rpm.","salesMarkdown":"## Motor form factor and mechanical interface The SH30553P11F2100 uses a 55 mm international standard flange (IEC 60034-5) with a 40 mm centring collar and 0.08 in (2 mm) centring collar depth — mates directly to common gearbox input flanges without an adapter plate. Shaft is 0.4 in (9 mm) diameter, 0.8 in (20 mm) length, with a parallel key 0.1 in (3 mm) wide — standard for coupling to timing pulleys or direct-drive loads. Overall length 8.0 in (203 mm) from the mounting face to the rear of the housing; the rotatable right-angled connector exits the motor body, allowing cable routing in tight cabinet layouts. ## Supply voltage and speed trade-offs This is a three-phase servo motor, but it operates on single-phase supply at reduced output — nominal speed drops to 2000 rpm at 115 V single phase and 4000 rpm at 230 V single phase, versus 6000 rpm at both 400 V and 480 V three-phase. Nominal output power follows the same pattern: 240 W at 115 V single phase, 460 W at 230 V single phase, 880 W at 400 V three phase, and 970 W at 480 V three phase — the three-phase supply delivers the full rated continuous power of 680 W. Maximum mechanical speed is 9000 rpm, giving headroom above the nominal speed for high-speed spindle or rapid-traverse moves, but the torque curve drops above 6000 rpm — the maximum radial force Fr declines from 390 N at 1000 rpm to 200 N at 7000 rpm. ## Feedback and holding brake for vertical-axis duty The absolute single-turn SinCos Hiperface encoder provides position feedback at power-up without a homing cycle — the drive reads the absolute position within one revolution, critical for tool-change or Z-axis positions that must repeat shot after shot. Integrated holding brake delivers 0.8 N.m (7.08 lbf.in) holding torque — sufficient to hold a vertical load on a gantry or press axis when the servo drive is disabled, preventing drift during power-off or E-stop conditions. Continuous stall torque is 1.05 N.m (9.29 lbf.in) at 115-480 V three phase, with a peak stall torque of 3.5 N.m (31.0 lbf.in) — the brake torque sits below the continuous stall, so the brake does not limit the motor's rated torque output. ## Environmental rating and thermal management IP65 rating on both the motor body and the shaft bushing per IEC 60034-5 — the seal at the shaft exit prevents coolant ingress in machining environments, and the housing withstands washdown in food-processing lines. Cooling is natural convection — no external fan or water jacket required, which simplifies installation but means the 680 W continuous power rating assumes free airflow around the motor body; derating applies in enclosed gearbox mounts. Stator resistance is 10.4 Ohm and stator inductance 37.98 mH — these values set the I²R copper losses and the current-loop bandwidth the drive must handle; the torque constant is 0.62 N.m/A at 120 °C copper temperature.","metaTitle":"Schneider Electric SH30553P11F2100 Servo Motor with Brake","metaDescription":"Schneider Electric SH30553P11F2100 servo motor with brake, 680 W continuous power, 55 mm flange, IP65, absolute single-turn Hiperface encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":[],"specifications":{"Length":"8.0 in (203 mm)","Product Status":"Active","Shaft Diameter":"0.4 in (9 mm)","Shaft End Type":"Parallel key","Max Axial Force Fa N":"40 N","Max Radial Force Fr N":"190 N 8000 rpm 390 N 1000 rpm 310 N 2000 rpm 270 N 3000 rpm 240 N 4000 rpm 230 N 5000 rpm 210 N 6000 rpm 200 N 7000 rpm","Centring Collar Diameter":"1.6 in (40 mm)","Main Product Or Component Type":"Servo motor"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/69623d08aff48b934858078658e7b693.pdf","sourceUrl":"https://www.se.com/nl/en/product/SH30553P11F2100/sh3-servomotor-55mm-3-stacks-keyed-shaft-sincos-singleturn-128-brake-angular-ip65-65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH30553P11F2100/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH30553P11F2100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH30553P11F2100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}