{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH30702P1AF4100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH30702P1AF4100","canonicalUrl":"https://aoctrl.com/schneider/SH30702P1AF4100","factsUrl":"https://aoctrl.com/api/mcp/products/SH30702P1AF4100","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH30702P1AF4100 SH3 servo motor with holding brake, 1130 W continuous power, 6000 rpm nominal speed at 400 V three-phase, 3 N.m holding brake torque, absolute single-turn Hiperface DSL encoder, IP65, 70 mm flange.","salesMarkdown":"## Speed and torque depend on your supply voltage The SH30702P1AF4100: This motor delivers 3000 rpm on 230 V single-phase input, 6000 rpm on 400 V three-phase, and 7200 rpm on 480 V three-phase. The nominal torque drops from 2.1 N.m at 230 V to 1.8 N.m at 400/480 V — the winding is optimized for the higher voltage range, so the torque-per-amp is lower on three-phase. Continuous power is 1130 W on three-phase supplies; on 230 V single-phase it's 610 W. If your line runs 230 V single-phase, budget for the reduced power ceiling. ## Brake is for holding, not stopping The holding brake delivers 3 N.m static torque — it locks the rotor when power is removed, preventing a vertical load from dropping. It is not rated for dynamic braking; use the drive's regenerative braking or an external resistor for deceleration. Brake pull-in power is 7 W, typically supplied by a 24 VDC auxiliary supply. ## Encoder choice saves a homing cycle The absolute single-turn Hiperface DSL encoder reports position on power-up — no homing or reference run needed after a power cycle. This cuts commissioning time on multi-axis machines and eliminates the home sensor wiring. ## IP65 lets it handle washdown Both the motor body and the shaft bushing are rated IP65 per IEC 60034-5. The connector seal must be properly mated to maintain the rating. ## Thermal limits and current draw Maximum continuous current is 11.8 A, and the same value applies for the 3-second peak output — the drive must be sized to deliver this peak without tripping. The torque constant is 0.7 N.m/A at 120 °C copper temperature; at room temperature it will be slightly higher, but use the hot value for thermal sizing. Stator resistance is 4.2 Ohm and inductance is 10.65 mH, giving an electrical time constant around 2.5 ms. The drive's current loop gains should be tuned to this time constant for stable torque control. ## Mechanical fit and shaft loading The motor mounts on a 70 mm international standard flange. Overall length is 213 mm, shaft diameter 11 mm with a 23 mm shaft length and 4 mm key width. Centring collar depth is 2.5 mm — confirm the mating pilot bore depth. Maximum radial force is 990 N at 1000 rpm; maximum axial force is 160 N. These are bearing life limits — belt tension or gear thrust loads must stay within these values at the operating speed.","metaTitle":"Schneider Electric SH30702P1AF4100 Servo Motor with Brake","metaDescription":"Schneider Electric SH30702P1AF4100 SH3 servo motor with holding brake.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH30702P1AF4100","Length":"8.4 in (213 mm)","Inertia":"0.072 kg.cm² of brake 0.41 kg.cm² of motor","Category":"US1PC5218359","Key width":"0.2 in (4 mm)","Shaft end":"Parallel key","description":"SH3 servomotor, 70mm, 2 stacks, keyed Shaft, Singleturn DSL 18bit, Brake, OneMotorCable angular M23, IP65/65","Encoder type":"Absolute single turn Hiperface DSL","Shaft length":"0.9 in (23 mm)","Holding brake":"With","Nominal speed":"3000 rpm 230 V single phase 6000 rpm 400 V three phase 7200 rpm 480 V three phase","Rotor inertia":"0.482 kg.cm²","Holding torque":"26.6 lbf.in (3 N.m)","Nominal torque":"18.6 lbf.in (2.1 N.m) 230 V single phase 15.9 lbf.in (1.8 N.m) 400 V three phase 15.9 lbf.in (1.8 N.m) 480 V three phase","Shaft diameter":"0.4 in (11 mm)","Torque constant":"0.7 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"1130 W","Mounting Support":"International standard flange","Sizing reference":"SH30702P","Back emf constant":"48 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"2.8 in (70 mm)","Peak stall torque":"67.3 lbf.in (7.6 N.m) 115...480 V three phase","Stator inductance":"10.65 mH","Stator resistance":"4.2 Ohm","Brake pull-in power":"7 W","Maximum current Irms":"11.8 A","Nominal output power":"610 W 230 V single phase 1130 W 400 V three phase 1130 W 480 V three phase","Centring collar depth":"0.10 in (2.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"quicklock rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"3.0","Maximum axial force Fa":"160 N","Output current 3s peak":"11.8 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"18.06 lbf.in (2.04 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"990 N 1000 rpm","Mounting holes diameter":"0.2 in (5.5 mm)","Centring collar diameter":"2.4 in (60 mm)","Continuous stall current":"2.9 A","Maximum mechanical speed":"8000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"262144 points/turn","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"3.2 in (82 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$1,583.82","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/e4e010f61da29ce73ba31eae02112489.pdf","sourceUrl":"https://www.se.com/ie/en/product/SH30702P1AF4100/sh3-servomotor-70mm-2-stacks-keyed-shaft-singleturn-dsl-18bit-brake-onemotorcable-angular-m23-ip65-65/"},"ai":{"faq":[{"question":"What supply voltage gives the highest speed on SH30702P1AF4100?","answer":"480 V three-phase delivers 7200 rpm nominal speed. At 400 V three-phase it runs 6000 rpm; at 230 V single-phase it runs 3000 rpm."},{"question":"What is the holding brake torque on this servo motor?","answer":"The holding brake provides 3 N.m static torque. It is designed to hold the load at rest when power is removed, not for dynamic stopping."},{"question":"What encoder type does SH30702P1AF4100 use?","answer":"It uses an absolute single-turn Hiperface DSL encoder. This eliminates the need for a homing cycle on power-up."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH30702P1AF4100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH30702P1AF4100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}