{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH30703P0AF3000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH30703P0AF3000","canonicalUrl":"https://aoctrl.com/schneider/SH30703P0AF3000","factsUrl":"https://aoctrl.com/api/mcp/products/SH30703P0AF3000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor, SH30703P0AF3000, three-phase, 1330 W continuous power, 3000-7200 rpm, absolute single-turn Hiperface DSL encoder, with holding brake, IP65, smooth shaft.","salesMarkdown":"## Motor specs and drive pairing constraints The SH30703P0AF3000 is a three-phase servo motor from the SH3 series, delivering 1330 W continuous power at 400 V or 480 V three-phase supply (830 W at 230 V single phase). Nominal speed ranges from 3000 rpm on 230 V single phase up to 7200 rpm on 480 V three phase — the speed-torque curve shifts with the supply voltage, so the drive's DC bus voltage must match the target speed band. Nominal torque is 24.8 lbf.in (2.8 N.m) at 230 V single phase, dropping to 18.6 lbf.in (2.1 N.m) at 400/480 V three phase — the lower torque at higher voltage reflects the motor's constant-power region above base speed. The absolute single-turn Hiperface DSL encoder provides position feedback over a digital serial link, eliminating analog encoder cable noise issues — the drive must support Hiperface DSL protocol; check compatibility with your Lexium or third-party drive. ## Brake, inertia, and vertical-axis duty The integrated holding brake delivers 26.6 lbf.in (3 N.m) holding torque — sufficient to hold a vertical load at standstill without the drive holding the position electrically. Brake pull-in power is 7 W, so the brake coil draw is low enough for a standard 24 VDC control supply; the brake release time is typically in the tens of milliseconds — budget this into the sequence when the axis starts moving after a stop. The sizing reference SH30703P groups the motor family; confirm the encoder option and shaft configuration match your application before committing. Maximum RMS current is 17 A — size the drive and cable for at least this peak draw; the continuous stall current is 4.1 A, so the drive's continuous rating should cover the lower figure while the peak rating handles acceleration transients. ## Environmental sealing and mechanical integration The motor body carries IP65 protection — suitable for washdown and dusty environments. The shaft bushing without the shaft seal ring drops to IP54; if the application sees direct spray on the shaft exit, specify the optional shaft seal. Motor flange size is 2.8 in (70 mm) with a centring collar diameter of 2.4 in (60 mm) and a centring collar depth of 0.10 in (2.5 mm) — mounts to the standard IEC 70 mm flange pattern. Shaft diameter is 0.6 in (14 mm) with a smooth shaft — the smooth shaft means the coupling must be clamped or keyed; no keyway is provided, so use a shaft-locking coupling or add a keyway during installation. Electrical connection uses a rotatable right-angled connector and a quick-lock straight connector — the connector orientation can be adjusted after mounting, simplifying cable routing in tight panels.","metaTitle":"Schneider Electric SH30703P0AF3000 Servo Motor, 1330 W","metaDescription":"Schneider Electric SH30703P0AF3000 servo motor, 1330 W continuous power, 3-phase, 3000-7200 rpm. Absolute single-turn Hiperface DSL encoder, holding brake.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"9.7 in (246 mm)","Category":"US1PC5218359","Shaft end":"Smooth shaft","Encoder type":"Absolute single turn Hiperface DSL","Shaft length":"1.2 in (30 mm)","Holding brake":"With","Nominal speed":"3000 rpm 230 V single phase 6000 rpm 400 V three phase 7200 rpm 480 V three phase","Rotor inertia":"0.807 kg.cm²","Holding torque":"26.6 lbf.in (3 N.m)","Nominal torque":"24.8 lbf.in (2.8 N.m) 230 V single phase 18.6 lbf.in (2.1 N.m) 400 V three phase 18.6 lbf.in (2.1 N.m) 480 V three phase","Shaft diameter":"0.6 in (14 mm)","Torque constant":"0.72 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"1330 W","Mounting Support":"International standard flange","Sizing reference":"SH30703P","Back emf constant":"49 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"2.8 in (70 mm)","Peak stall torque":"100.01 lbf.in (11.3 N.m) 115...480 V three phase","Stator inductance":"14.6 mH","Stator resistance":"2.7 Ohm","Brake pull-in power":"7 W","Maximum current Irms":"17 A","Nominal output power":"830 W 230 V single phase 1330 W 400 V three phase 1330 W 480 V three phase","Centring collar depth":"0.10 in (2.5 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"quicklock straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"3","Maximum axial force Fa":"160 N","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"26.02 lbf.in (2.94 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5","Maximum radial force Fr":"1050 N 1000 rpm","Mounting holes diameter":"0.2 in (5.5 mm)","Centring collar diameter":"2.4 in (60 mm)","Continuous stall current":"4.1 A","Maximum mechanical speed":"8000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"262144 points/turn","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"3.2 in (82 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/f32d47f7ac8205886b7107545d406a10.pdf","sourceUrl":"https://www.se.com/ie/en/product/SH30703P0AF3000/sh3-servomotor-70mm-3-stacks-smooth-shaft-singleturn-dsl-18bit-brake-onemotorcable-straight-m23-ip54-65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH30703P0AF3000/alternatives.json"},"ai":{"faq":[{"question":"What is SH30703P0AF3000's listed phase and power rating?","answer":"It is a three-phase servo motor with 1330 W continuous power at 400/480 V three-phase supply, and 830 W at 230 V single phase. The nominal speed ranges from 3000 rpm to 7200 rpm depending on the supply voltage."},{"question":"What encoder type does the SH30703P0AF3000 use?","answer":"It uses an absolute single-turn Hiperface DSL encoder — a digital serial interface that provides position feedback without analog noise susceptibility. The drive must support Hiperface DSL protocol."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH30703P0AF3000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH30703P0AF3000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}