{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH30703P1AF4100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH30703P1AF4100","canonicalUrl":"https://aoctrl.com/schneider/SH30703P1AF4100","factsUrl":"https://aoctrl.com/api/mcp/products/SH30703P1AF4100","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor with brake, SH30703P1AF4100, three-phase, 1330 W continuous power, 2.8 N.m nominal torque, IP65, absolute single-turn Hiperface DSL encoder, holding brake 3 N.m.","salesMarkdown":"## Motor ratings and speed profile by supply voltage The SH30703P1AF4100 delivers nominal speed that depends on the supply: 3000 rpm at 230 V single-phase input, 6000 rpm at 400 V three-phase, and 7200 rpm at 480 V three-phase. This means the same motor frame covers both low-speed high-torque and high-speed low-torque applications depending on the drive voltage — useful when standardising one motor across multiple line voltages. Nominal torque is 2.8 N.m at 230 V single phase, dropping to 2.1 N.m at both 400 V and 480 V three phase. Continuous power is 1330 W at 400/480 V three phase, 830 W at 230 V single phase. The torque constant is 0.72 N.m/A at 120 °C copper temperature, so drive current sizing should use this value for thermal steady-state. Peak stall torque reaches 11.3 N.m at 115...480 V three phase, with a continuous stall torque of 2.94 N.m over the same voltage range. The 3-second peak current is 17.0 A — the drive's peak current capability must match this figure to avoid torque clipping during acceleration or reversing cycles. ## Encoder, brake, and environmental sealing Fitted with an absolute single-turn Hiperface DSL encoder. No homing routine is needed on power-up — the position is known immediately. This encoder protocol is compatible with Schneider drives (Lexium 32, 62) that support Hiperface DSL; confirm drive firmware version before commissioning. The holding brake delivers 3 N.m holding torque and consumes 7 W pull-in power. For vertical-axis applications, the brake holds the load at standstill without servo current, but the brake release time must be coordinated with the drive enable sequence to prevent load drop. IP65 protection on both the motor body and the shaft bushing, conforming to IEC 60034-5. This allows direct washdown exposure — suitable for food processing, beverage filling, or machining lines where coolant spray is present. The shaft seal is the wet-end barrier; the connector interface uses a straight or rotatable right-angle Quicklock connector. ## Mechanical interface and mounting Motor flange size is 70 mm (2.8 in) with a centring collar depth of 2.5 mm. The shaft diameter is 14 mm with a parallel key (key width 5 mm) and shaft length 30 mm. Overall motor length is 246 mm (9.7 in). Mounts to an international standard flange — compatible with common gearbox input flanges in this frame class. Maximum radial force Fr is 1070 N at 1000 rpm; maximum axial force Fa is 160 N. These limits govern belt-drive or direct-coupling selection — exceeding them shortens bearing life or causes shaft deflection that misaligns the encoder.","metaTitle":"Schneider SH30703P1AF4100 Servo Motor with Brake, 1330 W","metaDescription":"Schneider SH30703P1AF4100 servo motor, three-phase, 1330 W continuous, IP65, holding brake 3 N.m, Hiperface DSL encoder. Active production, quoted to order.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH30703P1AF4100","Length":"9.7 in (246 mm)","Inertia":"0.227 kg.cm² of brake 0.58 kg.cm² of motor","Category":"US1PC5218359","Key width":"0.2 in (5 mm)","Shaft end":"Parallel key","description":"SH3 servomotor, 70mm, 3 stacks, keyed Shaft, Singleturn DSL 18bit, Brake, OneMotorCable angular M23, IP65/65","Encoder type":"Absolute single turn Hiperface DSL","Shaft length":"1.2 in (30 mm)","Holding brake":"With","Nominal speed":"3000 rpm 230 V single phase 6000 rpm 400 V three phase 7200 rpm 480 V three phase","Rotor inertia":"0.807 kg.cm²","Holding torque":"26.6 lbf.in (3 N.m)","Nominal torque":"24.8 lbf.in (2.8 N.m) 230 V single phase 18.6 lbf.in (2.1 N.m) 400 V three phase 18.6 lbf.in (2.1 N.m) 480 V three phase","Shaft diameter":"0.6 in (14 mm)","Torque constant":"0.72 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"1330 W","Mounting Support":"International standard flange","Sizing reference":"SH30703P","Back emf constant":"49 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"2.8 in (70 mm)","Peak stall torque":"100.01 lbf.in (11.3 N.m) 115...480 V three phase","Stator inductance":"7.3 mH","Stator resistance":"2.7 Ohm","Brake pull-in power":"7 W","Maximum current Irms":"17.0 A","Nominal output power":"830 W 230 V single phase 1330 W 400 V three phase 1330 W 480 V three phase","Centring collar depth":"0.10 in (2.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"quicklock rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"3.0","Maximum axial force Fa":"160 N","Output current 3s peak":"17.0 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"26.02 lbf.in (2.94 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"1070 N 1000 rpm","Mounting holes diameter":"0.2 in (5.5 mm)","Centring collar diameter":"2.4 in (60 mm)","Continuous stall current":"4.1 A","Maximum mechanical speed":"8000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"262144 points/turn","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"3.2 in (82 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$1,693.44","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/1a8c1e7815d18fce137a3f02fea48692.pdf","sourceUrl":"https://www.se.com/nl/en/product/SH30703P1AF4100/sh3-servomotor-70mm-3-stacks-keyed-shaft-singleturn-dsl-18bit-brake-onemotorcable-angular-m23-ip65-65/"},"ai":{"faq":[{"question":"What encoder type does SH30703P1AF4100 use?","answer":"It uses an absolute single-turn Hiperface DSL encoder. Position is known immediately on power-up, eliminating the need for a homing sequence. Compatible with Schneider drives that support the Hiperface DSL protocol."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH30703P1AF4100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH30703P1AF4100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}