{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31001M02A2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31001M02A2200","canonicalUrl":"https://aoctrl.com/schneider/SH31001M02A2200","factsUrl":"https://aoctrl.com/api/mcp/products/SH31001M02A2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor, SH31001M02A2200, 660 W continuous power, 3000 rpm nominal at 400 V three-phase, 2.8 Nm, absolute multiturn SinCos Hiperface encoder, IP65 motor, IP67 housing, smooth shaft, no brake.","salesMarkdown":"## Supply-dependent speed and torque — the spec line that matters The SH31001M02A2200 is a three-phase servo motor, but its nominal speed and torque shift with the supply voltage — 625 rpm / 2.8 Nm at 115 V single-phase, 1250 rpm / 2.71 Nm at 230 V single-phase, 2500 rpm / 2.52 Nm at 400 V three-phase, and 3000 rpm / 2.52 Nm at 480 V three-phase. The nominal output power also varies: 210 W at 115 V single-phase, 410 W at 230 V single-phase, 790 W at 400 V three-phase, and 930 W at 480 V three-phase. Continuous power is 660 W — this is the thermal limit under natural convection cooling, so the motor's usable duty cycle depends on the actual load profile and ambient temperature. ## Encoder and feedback — Hiperface absolute multiturn The encoder is an absolute multiturn SinCos Hiperface type — this is a common open-standard feedback interface used by Schneider's Lexium drives and many third-party servo drives. Multiturn absolute means the encoder tracks position over multiple shaft revolutions even after power loss; the SinCos analog tracks provide fine interpolation for high-resolution positioning. The back EMF constant is 115 V/krpm at 68 °F (20 °C) — this sets the voltage-speed relationship and must match the drive's DC bus voltage headroom. ## No holding brake — plan for external braking This variant ships without a holding brake — the motor relies on the drive's holding torque or an external brake for vertical-axis or safety-hold applications. Continuous stall torque is 2.94 Nm across the 115–480 V three-phase range, with a peak stall torque of 9.6 Nm — the peak figure is available for acceleration but not for holding at standstill without a brake. ## IP rating and environmental sealing The motor body and shaft bushing are rated IP65, while the housing is rated IP67 — the housing seal is one class higher, meaning the connector area is better protected against immersion than the motor body itself. Cooling is by natural convection — no fan or forced air, so the motor relies on the mounting flange and ambient airflow for heat dissipation. ## Mechanical interface and mounting The motor uses an international standard flange with a 100 mm flange size, 95 mm centring collar diameter, and 3.5 mm centring collar depth — this is a standard IEC mounting pattern for servo motors in this power class. The shaft is 19 mm diameter, 40 mm long, smooth (no keyway), with a 6 mm key width — the smooth shaft means the coupling or pulley must use a clamping or friction-fit method. Maximum radial force is 900 N at 1000 rpm, derating to 530 N at 5000 rpm — this is the limiting factor for belt-drive or overhung-load applications; maximum axial force is 160 N. ## Electrical parameters and winding data Stator resistance is 13.9 Ohm and stator inductance is 99.15 mH — these are the winding parameters the drive's autotuning routine uses to set current loops and velocity gains. Maximum continuous current (Irms) is 6.3 A, with a continuous stall current of 1.8 A — the ratio between these tells you the motor's overload capability for short-duration peak moves. The torque constant is 1.63 Nm/A at 248 °F (120 °C) — this is the hot winding value, so expect slightly higher torque per amp when the motor is cold. The motor has 4 poles and a maximum mechanical speed of 6000 rpm — the electrical frequency at 6000 rpm is 200 Hz, which the drive's output stage must support. The electrical connection uses a straight connector and a rotatable right-angled connector — the right-angled option allows cable exit in tight panel layouts.","metaTitle":"Schneider Electric SH31001M02A2200 Servo Motor, 660 W","metaDescription":"Schneider Electric SH31001M02A2200 SH3 servo motor, 660 W continuous, 3000 rpm at 400 V three-phase, 2.8 Nm, absolute multiturn Hiperface encoder, IP65/IP67.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"6.6 in (168.5 mm)","Key width":"0.2 in (6 mm)","Shaft end":"Smooth shaft","Encoder type":"Absolute multiturn SinCos Hiperface","Shaft length":"1.6 in (40 mm)","Holding brake":"Without","Nominal speed":"625 rpm 115 V single phase 1250 rpm 230 V single phase 2500 rpm 400 V three phase 3000 rpm 480 V three phase","Rotor inertia":"1.4 kg.cm²","Nominal torque":"24.8 lbf.in (2.8 N.m) 115 V single phase 23.99 lbf.in (2.71 N.m) 230 V single phase 22.30 lbf.in (2.52 N.m) 400 V three phase 22.30 lbf.in (2.52 N.m) 480 V three phase","Shaft diameter":"0.7 in (19 mm)","Torque constant":"1.63 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"660 W","Mounting Support":"International standard flange","Sizing reference":"SH31001M","Back emf constant":"115 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"85.0 lbf.in (9.6 N.m) 115...480 V three phase","Stator inductance":"99.15 mH","Stator resistance":"13.9 Ohm","Maximum current Irms":"6.3 A","Nominal output power":"210 W 115 V single phase 410 W 230 V single phase 790 W 400 V three phase 930 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"4","Maximum axial force Fa":"160 N","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"26.02 lbf.in (2.94 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"900 N 1000 rpm 720 N 2000 rpm 630 N 3000 rpm 570 N 4000 rpm 530 N 5000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"1.8 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/667f1544780a552b738423b87279a395.pdf","sourceUrl":"https://www.se.com/vn/en/product/SH31001M02A2200/sh3-servomotor-100mm-1-stack-high-torque-smooth-shaft-sincos-multiturn-128-no-brake-angular-ip65-67/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH31001M02A2200/alternatives.json"},"ai":{"faq":[{"question":"What encoder type does SH31001M02A2200 use?","answer":"It uses an absolute multiturn SinCos Hiperface encoder — this is a common open-standard feedback interface compatible with Schneider Lexium drives and many third-party servo drives."},{"question":"Does SH31001M02A2200 include a holding brake?","answer":"No, this variant ships without a holding brake. For vertical-axis or safety-hold applications, an external brake or the drive's holding torque must be used."},{"question":"What is the IP rating of SH31001M02A2200?","answer":"The motor body and shaft bushing are rated IP65, while the housing is rated IP67 — the housing seal is one class higher, providing better protection against immersion at the connector area."},{"question":"What supply voltages does SH31001M02A2200 support?","answer":"It supports 115 V single-phase, 230 V single-phase, 400 V three-phase, and 480 V three-phase — each produces different nominal speed and torque values, with the highest performance at 480 V three-phase (3000 rpm, 2.52 Nm, 930 W)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31001M02A2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31001M02A2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}