{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31002M12F2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31002M12F2200","canonicalUrl":"https://aoctrl.com/schneider/SH31002M12F2200","factsUrl":"https://aoctrl.com/api/mcp/products/SH31002M12F2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor with brake, SH31002M12F2200, 1.1 kW continuous power, 9 Nm holding torque, absolute multiturn SinCos Hiperface encoder, IP65/IP67, 100 mm flange.","salesMarkdown":"## Motor envelope and mounting — 100 mm flange, 235.5 mm body The SH31002M12F2200 uses an international standard flange with a 100 mm bolt circle and 95 mm centring collar, 3.5 mm deep. Overall body length is 235.5 mm — measure the available cavity before ordering, especially in retrofit cabinets where the old motor was shorter. Shaft is 19 mm diameter with a parallel key, 40 mm shaft length, 6 mm key width. The shaft bushing and housing both carry IP65 per IEC 60034-5; the housing alone is IP67 — this motor survives washdown if the cable connector is properly mated. ## Speed-torque map across supply voltages Nominal speed depends on the drive supply: 500 rpm at 115 V single-phase, 1000 rpm at 230 V single-phase, 2000 rpm at 400 V three-phase, and 2400 rpm at 480 V three-phase. Nominal torque drops slightly from 5.62 Nm at 115 V to 5.28 Nm at 400/480 V three-phase — the torque curve is flat across the voltage range, so the motor doesn't lose much grunt when you step up the line. Continuous stall torque is 5.8 Nm across the three-phase range (115 to 480 V). Peak stall torque hits 18.3 Nm — useful for breakaway or short overloads, but the 9.0 A peak current limit (3 s) governs how long you can hold that peak before the drive trips. ## Brake and feedback — holding torque and encoder type Feedback is an absolute multiturn SinCos Hiperface encoder. No homing sequence needed after power loss — the drive reads absolute position on power-up. Confirm the drive model supports Hiperface protocol; not all servo drives do. ## Electrical parameters for drive tuning Stator resistance is 8.6 Ω, inductance 24.3 mH — these set the current-loop tuning gains. Torque constant is 2.32 Nm/A at 120 °C copper temperature; back EMF constant is 146 V/krpm at 20 °C. The 4-pole motor (1500 rpm synchronous at 50 Hz) means the drive's velocity loop gains will differ from a 6- or 8-pole machine. Continuous power is 1100 W, but nominal output power varies with supply: 300 W at 115 V single-phase, 580 W at 230 V single-phase, 1090 W at 400 V three-phase, 1280 W at 480 V three-phase. The motor is naturally convection-cooled — no fan, so don't bury it in a tight enclosure without airflow.","metaTitle":"Schneider Electric SH31002M12F2200 Servo Motor with Brake","metaDescription":"Schneider Electric SH31002M12F2200 SH3 servo motor with brake, 1.1 kW continuous, 9 Nm holding torque, IP65/IP67, absolute multiturn encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"9.3 in (235.5 mm)","Inertia":"0.618 kg.cm² of brake 2.31 kg.cm² of motor","Key width":"0.2 in (6 mm)","Shaft end":"Parallel key","Encoder type":"Absolute multiturn SinCos Hiperface","Shaft length":"1.6 in (40 mm)","Holding brake":"With","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"2.928 kg.cm²","Holding torque":"79.7 lbf.in (9 N.m)","Nominal torque":"49.74 lbf.in (5.62 N.m) 115 V single phase 48.7 lbf.in (5.5 N.m) 230 V single phase 46.73 lbf.in (5.28 N.m) 400 V three phase 46.73 lbf.in (5.28 N.m) 480 V three phase","Shaft diameter":"0.7 in (19 mm)","Torque constant":"2.32 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"1100 W","Mounting Support":"International standard flange","Sizing reference":"SH31002M","Back emf constant":"146 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"162.0 lbf.in (18.3 N.m) 115...480 V three phase","Stator inductance":"24.3 mH","Stator resistance":"8.6 Ohm","Maximum current Irms":"9.0 A","Nominal output power":"300 W 115 V single phase 580 W 230 V single phase 1090 W 400 V three phase 1280 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"4","Maximum axial force Fa":"160 N","Output current 3s peak":"9.0 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"51.3 lbf.in (5.8 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"990 N 1000 rpm 790 N 2000 rpm 690 N 3000 rpm 620 N 4000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"2.5 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/bd3c7de818a1146bf55a87075815f145.pdf","sourceUrl":"https://www.se.com/vn/en/product/SH31002M12F2200/sh3-servomotor-100mm-2-stacks-high-torque-keyed-shaft-sincos-multiturn-128-brake-angular-ip65-67/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH31002M12F2200/alternatives.json"},"ai":{"faq":[{"question":"What is the holding torque of the brake on the SH31002M12F2200?","answer":"The holding brake delivers 9 Nm (79.7 lbf·in) of holding torque. This is sufficient to hold vertical-axis loads without the drive supplying current to the motor windings."},{"question":"What encoder type does the SH31002M12F2200 use?","answer":"It uses an absolute multiturn SinCos Hiperface encoder. Absolute position is retained after power loss, eliminating the need for a homing routine on startup. Verify your servo drive supports the Hiperface protocol."},{"question":"What IP rating does the SH31002M12F2200 have?","answer":"The motor body and shaft bushing are IP65 rated; the housing alone is IP67 per IEC 60034-5. This means the motor withstands washdown environments when the cable connector is properly sealed."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31002M12F2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31002M12F2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}