{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31003M01A2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31003M01A2200","canonicalUrl":"https://aoctrl.com/schneider/SH31003M01A2200","factsUrl":"https://aoctrl.com/api/mcp/products/SH31003M01A2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor, SH31003M01A2200, three-phase, 1.5 kW continuous power, 7.8 Nm nominal torque at 400 V, 2000 rpm, absolute single-turn SinCos Hiperface encoder, IP65, smooth shaft, without brake.","salesMarkdown":"## Motor ratings across supply voltages The SH31003M01A2200 delivers 1.5 kW continuous power from a 400 V three-phase supply, with nominal torque of 7 N.m at that voltage. On a 480 V three-phase line it produces 6.76 N.m at 2400 rpm, while single-phase 115 V and 230 V supplies yield lower torque and speed — 7.8 N.m at 500 rpm and 7.5 N.m at 1000 rpm respectively. The peak stall torque reaches 28.3 N.m across the 115–480 V three-phase range, which sets the acceleration ceiling for the driven load. ## Feedback and environmental sealing The absolute single-turn SinCos Hiperface encoder reports position on power-up without a homing cycle, which holds the unit on the grid for applications that cannot tolerate a reference move after a power loss. The IP65 rating on the motor body and shaft bushing, plus IP67 on the housing, means this motor withstands washdown environments — the sealing washer at the connector interface is the wet-end barrier, not the housing thread. Cooling is by natural convection only, so the motor relies on its own surface area and the mounting flange to dissipate heat. In a confined panel or high-ambient enclosure, the continuous torque must be derated below the 8 N.m figure to stay within the 130 °C copper hot-spot limit. ## Mechanical interface and mounting The motor uses an international standard flange with a 100 mm flange size and a 95 mm centring collar that locates the motor concentric to the load. The smooth shaft measures 19 mm diameter by 40 mm length with a 6 mm keyway — the absence of a holding brake means the load must be held by the servo drive's holding current or an external brake when power is removed. Maximum radial force at the shaft is 1050 N at 1000 rpm, dropping to 660 N at 4000 rpm — the bearing life follows the inverse cube of the radial load, so a belt-driven load applying 800 N at 2000 rpm (830 N limit) is acceptable, but the same load at 3000 rpm (730 N limit) would shorten bearing service life.","metaTitle":"Schneider Electric SH31003M01A2200 Servo Motor, 1.5 kW","metaDescription":"Schneider Electric SH31003M01A2200 SH3 servo motor, 1.5 kW continuous power, 7.8 Nm nominal torque at 400 V three-phase.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"9.5 in (240.5 mm)","Inertia":"0.0 kg.cm² of brake 3.22 kg.cm² of motor","Key width":"0.2 in (6 mm)","Shaft end":"Smooth shaft","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"1.6 in (40 mm)","Holding brake":"Without","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"3.22 kg.cm²","Nominal torque":"69.04 lbf.in (7.8 N.m) 115 V single phase 66.4 lbf.in (7.5 N.m) 230 V single phase 62.0 lbf.in (7 N.m) 400 V three phase 59.83 lbf.in (6.76 N.m) 480 V three phase","Shaft diameter":"0.7 in (19 mm)","Torque constant":"2.35 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"1500 W","Mounting Support":"International standard flange","Sizing reference":"SH31003M","Back emf constant":"148 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"250.5 lbf.in (28.3 N.m) 115...480 V three phase","Stator inductance":"17.4 mH","Stator resistance":"5.3 Ohm","Maximum current Irms":"14.7 A","Nominal output power":"410 W 115 V single phase 790 W 230 V single phase 1470 W 400 V three phase 1700 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"4","Maximum axial force Fa":"160 N","Output current 3s peak":"14.7 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"70.8 lbf.in (8 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"1050 N 1000 rpm 830 N 2000 rpm 730 N 3000 rpm 660 N 4000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"3.4 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/916c0499022cda945eee9feca1a20eaf.pdf","sourceUrl":"https://www.se.com/ca/en/product/SH31003M01A2200/sh3-servomotor-100mm-3-stacks-high-torque-smooth-shaft-sincos-singleturn-128-no-brake-angular-ip65-67/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH31003M01A2200/alternatives.json"},"ai":{"faq":[],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31003M01A2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31003M01A2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}