{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31004P0BF4000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31004P0BF4000","canonicalUrl":"https://aoctrl.com/schneider/SH31004P0BF4000","factsUrl":"https://aoctrl.com/api/mcp/products/SH31004P0BF4000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series SH31004P0BF4000 servo motor with brake, three-phase, 2.5 kW continuous power, 12 N·m holding torque, IP65, absolute multiturn Hiperface DSL encoder, smooth shaft, 100 mm flange.","salesMarkdown":"The SH31004P0BF4000 is a Schneider Electric SH3 series servo motor with an integrated holding brake, rated for 2.5 kW continuous power and 12 N·m holding torque. The brake holds the vertical axis in position when power is removed — a common requirement for Z-axis or gravity-loaded applications where the load must not drift after a stop. The nominal torque varies with the supply voltage: 9.5 N·m on 230 V single-phase, 7.9 N·m on 400 V three-phase, and 6.9 N·m on 480 V three-phase. The peak stall torque reaches 40.5 N·m across the 115...480 V three-phase range, so the motor can deliver short bursts of high torque for acceleration or overcoming static friction. The nominal speed also depends on the supply: 1500 rpm at 230 V single-phase, 3000 rpm at 400 V three-phase, and 3600 rpm at 480 V three-phase. This means the same motor frame can serve different line voltages, but the speed-torque curve shifts — you size the drive and gearing for the actual supply voltage on site. ## Absolute multiturn Hiperface DSL encoder — no homing cycle needed after power loss The motor carries an absolute multiturn Hiperface DSL encoder. Because it tracks position over multiple revolutions even when unpowered, the controller knows the exact shaft position at power-up — no homing sequence, no reference run. This saves cycle time on machines that power-cycle between shifts or after a fault. The encoder communicates over the Hiperface DSL protocol, which combines power and data on a single cable pair. That means fewer wires in the cable track and a simpler connector interface compared to separate encoder and motor power cables. ## IP65 motor body, natural convection — no fan, no filter to clean The motor enclosure is rated IP65 per IEC 60034-5, meaning it is dust-tight and protected against low-pressure water jets from any direction. The shaft bushing without the shaft seal ring drops to IP54 — if the application sees direct washdown aimed at the shaft exit, fit the optional seal ring to keep the rating. Cooling is by natural convection — no fan, no filter, no forced air. This eliminates a maintenance item and keeps the motor envelope clean, but the thermal budget depends on the mounting surface and ambient air movement. The motor's continuous stall torque of 10 N·m (115...480 V three-phase) assumes free convection in still air at rated ambient. ## Smooth shaft, 100 mm flange — mounting and coupling considerations The shaft is smooth (no keyway) with a 24 mm diameter and 50 mm length. A smooth shaft means the coupling or pulley must use a clamping or friction-fit method — no key to transmit torque. Verify the coupling bore and clamping mechanism match a 24 mm smooth shaft before assembly. The motor flange size is 100 mm (3.9 inches) with an international standard flange pattern. Mounting holes are 9.0 mm diameter on the flange, and the centring collar depth is 3.5 mm. The overall length of the motor body is 307.5 mm (12.1 inches). For current pricing and availability, submit an RFQ against this order code. The supply posture is confirmed at quote time — no stock-holding claim is made here.","metaTitle":"Schneider Electric SH31004P0BF4000 Servo Motor with Brake","metaDescription":"Schneider Electric SH31004P0BF4000 servo motor with brake, 2.5 kW continuous power, 12 N·m holding torque, IP65, absolute multiturn Hiperface DSL encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH31004P0BF4000","Length":"12.1 in (307.5 mm)","Inertia":"1.025 kg.cm² of brake 0.0 kg.cm² of motor","Category":"US1PC5218359","Shaft end":"Smooth shaft","description":"SH3 servomotor, 100mm, 4 stacks, smooth Shaft, Multiturn DSL 18bit, Brake, OneMotorCable angular M23, IP54/65","Encoder type":"Absolute multiturn Hiperface DSL","Shaft length":"2.0 in (50 mm)","Holding brake":"With","Nominal speed":"1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase","Rotor inertia":"5.245 kg.cm²","Holding torque":"106.2 lbf.in (12 N.m)","Nominal torque":"84.08 lbf.in (9.5 N.m) 230 V single phase 69.9 lbf.in (7.9 N.m) 400 V three phase 61.07 lbf.in (6.9 N.m) 480 V three phase","Shaft diameter":"0.9 in (24 mm)","Torque constant":"1.62 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"2500 W","Mounting Support":"International standard flange","Sizing reference":"SH31004P","Back emf constant":"103 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"358.5 lbf.in (40.5 N.m) 115...480 V three phase","Stator inductance":"13 mH","Stator resistance":"1.8 Ohm","Brake pull-in power":"18 W","Maximum current Irms":"32.3 A","Nominal output power":"1490 W 230 V single phase 2480 W 400 V three phase 2480 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"quicklock rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"4.0","Maximum axial force Fa":"20 N","Output current 3s peak":"32.3 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"88.5 lbf.in (10 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5","Maximum radial force Fr":"100 N 3000 rpm 145 N 1000 rpm 115 N 2000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"6.2 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"262144 points/turn x 4096 turns","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$2,468.34","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/dafc3590b34102247504740a9b13c066.pdf","sourceUrl":"https://www.se.com/us/en/product/SH31004P0BF4000/sh3-servomotor-100mm-4-stacks-smooth-shaft-multiturn-dsl-18bit-brake-onemotorcable-angular-m23-ip54-65/"},"ai":{"faq":[{"question":"How do I get current pricing and availability for SH31004P0BF4000?","answer":"Submit an RFQ against this order code. No stock-holding claim is made here."},{"question":"What is SH31004P0BF4000's listed phase and length?","answer":"The motor is a three-phase servo motor. Its overall body length is 307.5 mm (12.1 inches). The flange size is 100 mm (3.9 inches) with an international standard flange pattern."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31004P0BF4000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31004P0BF4000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}