{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31004P11F1100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31004P11F1100","canonicalUrl":"https://aoctrl.com/schneider/SH31004P11F1100","factsUrl":"https://aoctrl.com/api/mcp/products/SH31004P11F1100","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH31004P11F1100, SH3 series servo motor with holding brake, 2.5 kW continuous power, 40.5 Nm peak stall torque, IP65, absolute single-turn Hiperface encoder, 100 mm flange.","salesMarkdown":"## Speed-torque envelope across supply voltages The SH31004P11F1100: This motor delivers 9.9 Nm nominal torque at 750 rpm on 115 V single-phase, 9.5 Nm at 1500 rpm on 230 V single-phase, 7.9 Nm at 3000 rpm on 400 V three-phase, and 6.9 Nm at 3600 rpm on 480 V three-phase — the speed ceiling and torque density shift with the supply, so the drive and line voltage must match the target duty point. Continuous power is 2500 W, with nominal output power ranging from 780 W on 115 V single-phase up to 2600 W on 480 V three-phase — the motor is wound for the higher voltage range; single-phase operation derates both torque and power significantly. Peak stall torque reaches 40.5 Nm across the 115–480 V three-phase range, backed by a 32.3 A peak current capability — this is the figure for acceleration and emergency stop sizing, not continuous duty. ## Holding brake and mechanical interface The integrated holding brake delivers 12 Nm holding torque — sufficient to hold a vertical load at rest without power to the motor windings, but the brake is not rated for dynamic stopping; the drive handles deceleration. Mounting uses a 100 mm international standard flange with a 9.0 mm bolt circle and 3.5 mm centring collar depth — the shaft is 24 mm diameter with a parallel key, 50 mm shaft length, and 8 mm key width. ## Feedback, cooling, and environmental sealing Feedback is an absolute single-turn SinCos Hiperface encoder — no homing sequence needed on power-up for single-turn applications; the absolute position is known immediately, which simplifies commissioning and recovery after a power loss. Cooling is natural convection — no fan, so the thermal budget depends entirely on the mounting surface and ambient airflow; the copper hot-spot temperature is rated at 130 °C, and the torque constant is specified at 120 °C winding temperature. ## Electrical parameters for drive tuning Stator resistance is 1.81 Ω and inductance is 18.35 mH — these set the electrical time constant and influence the current-loop tuning gains in the servo drive; the back EMF constant is 103 V/krpm at 20 °C, which determines the voltage required at a given speed. Maximum continuous current is 32.3 A rms — the drive must be sized to supply this current continuously at the target torque; the 4-pole construction gives a base speed range suited to the 3000–3600 rpm nominal speeds on three-phase supply. Radial force limits are 1070 N at 1000 rpm, 850 N at 2000 rpm, and 740 N at 3000 rpm; maximum axial force is 160 N — these constrain the belt tension or direct-coupling overhung load the shaft bearings can sustain. ## Sourcing and lifecycle — current production, quoted to order The sizing reference is SH31004P — this is the family base code; the full order code SH31004P11F1100 specifies the connector variant (rotatable right-angled or straight connector), encoder type, and brake option.","metaTitle":"Schneider Electric SH31004P11F1100 Servo Motor with Brake","metaDescription":"Schneider Electric SH31004P11F1100 servo motor with holding brake, 2.5 kW continuous, 40.5 Nm peak torque, IP65, absolute encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"12.1 in (307.5 mm)","Inertia":"1.025 kg.cm² of brake 0.0 kg.cm² of motor","Category":"18359-PACDRIVE3 SERVO MOTORS","Key width":"0.3 in (8 mm)","Shaft end":"Parallel key","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"2.0 in (50 mm)","Holding brake":"With","Nominal speed":"750 rpm 115 V single phase 1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase","Rotor inertia":"5.245 kg.cm²","Holding torque":"106.2 lbf.in (12 N.m)","Nominal torque":"87.6 lbf.in (9.9 N.m) 115 V single phase 84.08 lbf.in (9.5 N.m) 230 V single phase 69.9 lbf.in (7.9 N.m) 400 V three phase 61.07 lbf.in (6.9 N.m) 480 V three phase","Shaft diameter":"0.9 in (24 mm)","Torque constant":"1.62 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"2500 W","Mounting Support":"International standard flange","Sizing reference":"SH31004P","Back emf constant":"103 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"358.5 lbf.in (40.5 N.m) 115...480 V three phase","Stator inductance":"18.35 mH","Stator resistance":"1.81 Ohm","Maximum current Irms":"32.3 A","Nominal output power":"780 W 115 V single phase 1490 W 230 V single phase 2480 W 400 V three phase 2600 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"4.0","Maximum axial force Fa":"160 N","Output current 3s peak":"32.3 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"88.5 lbf.in (10 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"1070 N 1000 rpm 850 N 2000 rpm 740 N 3000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"6.2 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/830aaf3c67222bf588100adb0ed6df5c.pdf","sourceUrl":"https://www.se.com/mk/en/product/SH31004P11F1100/sh3-servomotor-100mm-4-stacks-keyed-shaft-sincos-singleturn-128-brake-straight-ip65-65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH31004P11F1100/alternatives.json"},"ai":{"faq":[{"question":"What is the peak torque of SH31004P11F1100?","answer":"Peak stall torque is 40.5 Nm across the 115–480 V three-phase supply range, with a peak current capability of 32.3 A."},{"question":"What encoder type does SH31004P11F1100 use?","answer":"It uses an absolute single-turn SinCos Hiperface encoder — no homing sequence is needed on power-up for single-turn position feedback."},{"question":"What is the IP rating of this servo motor?","answer":"IP65 on both the motor body and the shaft bushing, conforming to IEC 60034-5 — suitable for washdown environments."},{"question":"What is the holding torque of the brake on SH31004P11F1100?","answer":"The integrated holding brake provides 12 Nm holding torque — designed to hold a load at rest, not for dynamic braking."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31004P11F1100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31004P11F1100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}