{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31004P12F1200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31004P12F1200","canonicalUrl":"https://aoctrl.com/schneider/SH31004P12F1200","factsUrl":"https://aoctrl.com/api/mcp/products/SH31004P12F1200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH31004P12F1200 SH3 servo motor with holding brake, 2500 W continuous power, three-phase, 4-pole, IP65/IP67, absolute multiturn SinCos Hiperface encoder, 100 mm flange, 24 mm shaft with parallel key.","salesMarkdown":"## Three-phase 4-pole servo with brake — drive pairing and speed range The SH31004P12F1200 is a three-phase, 4-pole servo motor from the SH3 series, rated 2500 W continuous power with natural convection cooling. The nominal speed depends on the supply voltage: 750 rpm at 115 V single-phase, 1500 rpm at 230 V single-phase, 3000 rpm at 400 V three-phase, and 3600 rpm at 480 V three-phase. The drive must be selected to match the target speed range and supply configuration. The holding brake delivers 12 N.m holding torque — enough to keep the load stationary when the drive is off. The brake is separate from the motor's electromagnetic torque; the continuous stall torque is 10 N.m across the 115–480 V three-phase range, and the peak stall torque reaches 40.5 N.m at 32.3 A peak current. The drive must supply that peak current for acceleration without tripping. ## Absolute multiturn Hiperface encoder — feedback protocol match The encoder is an absolute multiturn SinCos Hiperface type. This means the drive controller must support the Hiperface protocol to read position and speed feedback. The multiturn resolution tracks absolute position over multiple shaft revolutions, so the system does not need a homing cycle after power loss — useful for applications where the load position must be known immediately on restart. The torque constant is 1.62 N.m/A at 120 °C copper temperature, and the back EMF constant is 103 V/krpm at 20 °C. These values set the current-to-torque relationship and the voltage feedback the drive sees at speed — important for tuning the current loop and setting the velocity limit. ## IP65/IP67 sealing — washdown and environmental fit The motor body carries IP65 protection per IEC 60034-5, the shaft bushing is also IP65, and the housing is IP67. This means the motor withstands hose-directed water and temporary immersion — suitable for food processing, washdown, or outdoor installations where moisture ingress is a risk. The shaft bushing seal is the critical wear point; inspect it periodically in high-pressure washdown environments. The electrical connection uses a straight connector — no right-angle adapter, so plan for cable exit clearance. The motor flange is the international standard 100 mm size with a 3.5 mm centring collar depth and 9.0 mm mounting holes. The shaft is 24 mm diameter with a parallel key and 50 mm shaft length. ## Active production — sourcing and documentation The motor is supplied as a single unit. The sizing reference is SH31004P, which can be used to locate the matching drive and cable sets in the Schneider PACDrive 3 catalog. Compliance documentation (RoHS, REACH, UL, IEC) is available from the manufacturer; the IP ratings are certified to IEC 60034-5.","metaTitle":"Schneider Electric SH31004P12F1200 Servo Motor with Brake","metaDescription":"Schneider Electric SH31004P12F1200 servo motor with brake, 2500 W continuous power, 3-phase, 4-pole, IP65/IP67, absolute multiturn Hiperface encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"12.1 in (307.5 mm)","Inertia":"1.025 kg.cm² of brake 0.0 kg.cm² of motor","Category":"18359-PACDRIVE3 SERVO MOTORS","Key width":"0.3 in (8 mm)","Shaft end":"Parallel key","Encoder type":"Absolute multiturn SinCos Hiperface","Shaft length":"2.0 in (50 mm)","Holding brake":"With","Nominal speed":"750 rpm 115 V single phase 1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase","Rotor inertia":"5.245 kg.cm²","Holding torque":"106.2 lbf.in (12 N.m)","Nominal torque":"87.6 lbf.in (9.9 N.m) 115 V single phase 84.08 lbf.in (9.5 N.m) 230 V single phase 69.9 lbf.in (7.9 N.m) 400 V three phase 61.07 lbf.in (6.9 N.m) 480 V three phase","Shaft diameter":"0.9 in (24 mm)","Torque constant":"1.62 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"2500 W","Mounting Support":"International standard flange","Sizing reference":"SH31004P","Back emf constant":"103 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"358.5 lbf.in (40.5 N.m) 115...480 V three phase","Stator inductance":"18.35 mH","Stator resistance":"1.81 Ohm","Maximum current Irms":"32.3 A","Nominal output power":"780 W 115 V single phase 1490 W 230 V single phase 2480 W 400 V three phase 2600 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"4.0","Maximum axial force Fa":"160 N","Output current 3s peak":"32.3 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"88.5 lbf.in (10 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"1070 N 1000 rpm 850 N 2000 rpm 740 N 3000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"6.2 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/a025f5c392437d07911918cc1c201593.pdf","sourceUrl":"https://www.se.com/us/en/product/SH31004P12F1200/servo-motor-sh3-100-10nmkeymultibrakestr-connip65-ip676k-rpm/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH31004P12F1200/alternatives.json"},"ai":{"faq":[{"question":"What is the holding torque of the brake on SH31004P12F1200?","answer":"The holding brake delivers 106.2 lbf.in (12 N.m) holding torque. This is separate from the motor's continuous stall torque of 88.5 lbf.in (10 N.m) and peak stall torque of 358.5 lbf.in (40.5 N.m)."},{"question":"What encoder type does SH31004P12F1200 use?","answer":"It uses an absolute multiturn SinCos Hiperface encoder. The drive controller must support the Hiperface protocol to read position and speed feedback."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31004P12F1200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31004P12F1200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}