{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31004P1BF4000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31004P1BF4000","canonicalUrl":"https://aoctrl.com/schneider/SH31004P1BF4000","factsUrl":"https://aoctrl.com/api/mcp/products/SH31004P1BF4000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor with brake, SH31004P1BF4000, three-phase, 2.5 kW continuous power, 32.3 A peak current, absolute multiturn Hiperface DSL encoder, IP65, 100 mm flange.","salesMarkdown":"## Active production — no lifecycle risk for this SH3 servo The SH31004P1BF4000: The motor is a three-phase design, so the supply voltage must match one of the rated configurations: 1500 rpm at 230 V single-phase (derated), 3000 rpm at 400 V three-phase, or 3600 rpm at 480 V three-phase. The nominal torque and output power shift with each voltage — 9.5 N.m / 1490 W at 230 V single-phase, 7.9 N.m / 2480 W at 400 V three-phase, and 6.9 N.m / 2480 W at 480 V three-phase. Continuous power is 2500 W, with a peak stall torque of 40.5 N.m and continuous stall torque of 10 N.m across the 115...480 V three-phase range. The 32.3 A peak current rating sets the drive sizing floor — the servo drive must be capable of delivering this current for the acceleration/deceleration profile without tripping. ## Encoder, brake, and cooling — fit decisions for the controls integrator The encoder is an absolute multiturn Hiperface DSL type. This is a digital two-wire interface that carries both position data and power over the same pair — the servo drive must support Hiperface DSL protocol. There is no incremental encoder backup; the absolute position is retained on power cycle without a battery. Cooling is by natural convection only — no external fan or forced air required. This simplifies installation in clean or dusty environments but means the thermal time constant is longer; the motor relies on the IP65-rated housing (IEC 60034-5) to shed heat. Note the shaft bushing is IP54 without the shaft seal ring — a shaft seal upgrade may be needed for continuous washdown exposure. The electrical connection uses a rotatable right-angled connector with quicklock mechanism. This allows the cable exit orientation to be adjusted in 90° increments after mounting, which simplifies cable routing in tight cabinet or machine-frame spaces. ## Physical mounting envelope — flange, shaft, and mechanical interface The motor flange size is 100 mm (3.9 in) with a centring collar depth of 3.5 mm (0.1 in) — this is the standard IEC B5 flange pattern. The mounting support is listed as international standard flange, so it mates with the common 100 mm flange-mount gearboxes and mounting brackets. The shaft diameter is 24 mm (0.9 in) with a parallel key of 8 mm (0.3 in) width. Shaft length is 50 mm (2.0 in). The overall motor body length is 307.5 mm (12.1 in) — this is the dimension from the mounting face to the rear of the housing, excluding the connector and cable bend radius. Maximum radial force Fr is 145 N at 1000 rpm, derating to 115 N at 2000 rpm and 100 N at 3000 rpm. Maximum axial force Fa is 20 N. These limits govern belt-drive and direct-coupling applications — exceeding them risks bearing life reduction or shaft deflection. With an active lifecycle status, the SH31004P1BF4000 is sourced through authorized distribution channels. The sizing reference SH31004P identifies the frame and winding group; verify the BOM position matches this exact encoder and brake combination before ordering.","metaTitle":"Schneider Electric SH31004P1BF4000 Servo Motor with Brake","metaDescription":"Schneider Electric SH31004P1BF4000 SH3 servo motor with holding brake, 2.5 kW continuous, 32.3 A peak, absolute multiturn Hiperface DSL encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH31004P1BF4000","Length":"12.1 in (307.5 mm)","Inertia":"1.025 kg.cm² of brake 0.0 kg.cm² of motor","Category":"US1PC5218359","Key width":"0.3 in (8 mm)","Shaft end":"Parallel key","description":"SH3 servomotor, 100mm, 4 stacks, keyed Shaft, Multiturn DSL 18bit, Brake, OneMotorCable angular M23, IP54/65","Encoder type":"Absolute multiturn Hiperface DSL","Shaft length":"2.0 in (50 mm)","Holding brake":"With","Nominal speed":"1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase","Rotor inertia":"5.245 kg.cm²","Holding torque":"106.2 lbf.in (12 N.m)","Nominal torque":"84.08 lbf.in (9.5 N.m) 230 V single phase 69.9 lbf.in (7.9 N.m) 400 V three phase 61.07 lbf.in (6.9 N.m) 480 V three phase","Shaft diameter":"0.9 in (24 mm)","Torque constant":"1.62 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"2500 W","Mounting Support":"International standard flange","Sizing reference":"SH31004P","Back emf constant":"103 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"3.9 in (100 mm)","Peak stall torque":"358.5 lbf.in (40.5 N.m) 115...480 V three phase","Stator inductance":"13 mH","Stator resistance":"1.8 Ohm","Brake pull-in power":"18 W","Maximum current Irms":"32.3 A","Nominal output power":"1490 W 230 V single phase 2480 W 400 V three phase 2480 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"quicklock rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"4.0","Maximum axial force Fa":"20 N","Output current 3s peak":"32.3 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"88.5 lbf.in (10 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5","Maximum radial force Fr":"115 N 2000 rpm 100 N 3000 rpm 145 N 1000 rpm","Mounting holes diameter":"0.4 in (9.0 mm)","Centring collar diameter":"3.7 in (95 mm)","Continuous stall current":"6.2 A","Maximum mechanical speed":"6000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"262144 points/turn x 4096 turns","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"4.5 in (115 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$2,518.56","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/c84b46bc8ac449567e1928c08fa194f3.pdf","sourceUrl":"https://www.se.com/ie/en/product/SH31004P1BF4000/sh3-servomotor-100mm-4-stacks-keyed-shaft-multiturn-dsl-18bit-brake-onemotorcable-angular-m23-ip54-65/"},"ai":{"faq":[{"question":"What is the SH31004P1BF4000's phase configuration?","answer":"It is a three-phase motor. The rated speed and torque depend on the supply voltage: 1500 rpm / 9.5 N.m at 230 V single-phase (derated), 3000 rpm / 7.9 N.m at 400 V three-phase, or 3600 rpm / 6.9 N.m at 480 V three-phase."},{"question":"What is the physical length of the SH31004P1BF4000?","answer":"The overall motor body length is 307.5 mm (12.1 in), measured from the mounting face to the rear housing. This does not include the connector or cable bend radius."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31004P1BF4000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31004P1BF4000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}