{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH31403P01F1200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH31403P01F1200","canonicalUrl":"https://aoctrl.com/schneider/SH31403P01F1200","factsUrl":"https://aoctrl.com/api/mcp/products/SH31403P01F1200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series servo motor with brake, model SH31403P01F1200, three-phase, 4100 W continuous power, 24.7 Nm nominal torque, absolute single-turn SinCos Hiperface encoder, IP65/IP67, smooth shaft, 14.4 in length.","salesMarkdown":"## Motor specs that lock in the drive match The SH31403P01F1200: This SH3 frame servo is wound for three-phase supply and delivers 4100 W continuous power — the nominal torque lands at 24.7 Nm on 400 V three-phase, with a peak stall torque of 90.2 Nm across the 115–480 V three-phase range. The absolute single-turn SinCos Hiperface encoder gives position feedback on power-up without a home cycle, which saves time on multi-axis lines where the controller supports Hiperface protocol. ## Mounting and environmental fit Flange size is 140 mm (5.5 in) with an international standard flange pattern. Centring collar diameter is 130 mm, depth 3.5 mm — confirm the mating pilot bore before bolting down. The motor carries IP65 on the body and shaft bushing, IP67 on the housing — that means it survives washdown and hose-directed water, which is the usual spec for food-and-bev or high-hygiene lines. Cooling is natural convection, so no fan duct clearance needed, but the ambient heat sink matters. Smooth shaft, 24 mm diameter, 50 mm shaft length — the coupling or pulley bore must match; no keyway, so a clamp-type or friction-lock coupling is the install path. ## Brake and thermal limits The holding brake delivers 36 Nm — enough to hold a vertical load at rest without the drive holding torque active. That 36 Nm is the static holding value; dynamic braking capacity isn't listed here, so don't rely on it for emergency stops without checking the brake response time in the full motor drawing. Stator resistance is 0.4 Ω, inductance 2.66 mH — these set the electrical time constant and influence the drive's current-loop tuning. The torque constant is 1.58 Nm/A at 120 °C copper temperature; back EMF constant is 105 V/krpm at 20 °C. Maximum continuous current Irms is 61.0 A, same as the 3-second peak current — this motor can deliver full torque transient without a current fold-back for short bursts, but the thermal limit is set by the 130 °C copper hot-spot temperature.","metaTitle":"Schneider Electric SH31403P01F1200 Servo Motor with Brake","metaDescription":"Schneider Electric SH31403P01F1200 SH3 servo motor with brake, 4100 W continuous power, three-phase, IP65/IP67. Absolute single-turn SinCos Hiperface encoder.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH31403P01F1200","Length":"14.4 in (365.5 mm)","Inertia":"5.5 kg.cm² of brake 17.94 kg.cm² of motor","Category":"US1PC5218359","Shaft end":"Smooth shaft","description":"SH3 servomotor, 140mm, 3 stacks, smooth Shaft, SinCos Singleturn 128, Brake, straight, IP65/67","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"2.0 in (50 mm)","Holding brake":"With","Nominal speed":"750 rpm 115 V single phase 1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase","Rotor inertia":"23.44 kg.cm²","Holding torque":"318.6 lbf.in (36 N.m)","Nominal torque":"218.6 lbf.in (24.7 N.m) 115 V single phase 187.6 lbf.in (21.2 N.m) 230 V single phase 114.2 lbf.in (12.9 N.m) 400 V three phase 80.5 lbf.in (9.1 N.m) 480 V three phase","Shaft diameter":"0.9 in (24 mm)","Torque constant":"1.58 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"4100 W","Mounting Support":"International standard flange","Sizing reference":"SH31403P","Back emf constant":"105 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"5.5 in (140 mm)","Peak stall torque":"798.3 lbf.in (90.2 N.m) 115...480 V three phase","Stator inductance":"2.66 mH","Stator resistance":"0.4 Ohm","Maximum current Irms":"61.0 A","Nominal output power":"1940 W 115 V single phase 3330 W 230 V single phase 4050 W 400 V three phase 3430 W 480 V three phase","Centring collar depth":"0.1 in (3.5 mm)","Electrical Connection":"Straight connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"300 N","Output current 3s peak":"61.0 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"246.05 lbf.in (27.8 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"2420 N 1000 rpm 1920 N 2000 rpm 1670 N 3000 rpm","Mounting holes diameter":"0.4 in (11 mm)","Centring collar diameter":"5.1 in (130 mm)","Continuous stall current":"17.6 A","Maximum mechanical speed":"4000 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"6.5 in (165 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/0a38a5d55a8f698bd06917d23a7e4109.pdf","sourceUrl":"https://www.se.com/ie/en/product/SH31403P01F1200/sh3-servomotor-140mm-3-stacks-smooth-shaft-sincos-singleturn-128-brake-straight-ip65-67/"},"ai":{"faq":[{"question":"What is SH31403P01F1200's listed phase and power rating?","answer":"It is a three-phase servo motor with 4100 W continuous power. Nominal torque at 400 V three-phase is 24.7 Nm."},{"question":"What encoder type does this motor use?","answer":"An absolute single-turn SinCos Hiperface encoder. No homing sequence needed on power-up if the controller supports Hiperface."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH31403P01F1200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH31403P01F1200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}