{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32052P01A1000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32052P01A1000","canonicalUrl":"https://aoctrl.com/schneider/SH32052P01A1000","factsUrl":"https://aoctrl.com/api/mcp/products/SH32052P01A1000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series AC servo motor, three-phase, 7900 W continuous, 61.6 N.m nominal torque, IP65, SinCos Hiperface absolute single-turn feedback, SH32052P01A1000.","salesMarkdown":"## Sizing torque and speed into the drive The SH32052P01A1000 is the SH3 sizing reference SH32052P built around a five-pole three-phase stator that delivers a 64.9 N.m continuous stall torque across the full 115 to 480 V supply window and a 220 N.m peak stall ceiling for the short-duration acceleration duty a servo amplifier is sized to deliver (cites:,). Across that same supply range the rated operating points split cleanly: at 230 V single phase the motor carries 56 N.m nominal at 1000 rpm and 5860 W of mechanical output; at 400 V three phase it shifts to 38.1 N.m at 2000 rpm and 7980 W, with 480 V three phase holding 7140 W at 2400 rpm (cites:,). The 7980 W figure at 400 V three phase is the headline continuous rating and aligns with the listed 7900 W continuous power — that is the curve point the drive sizing tool should plot first, with the single-phase points reserved for sites where only 230 V control power is available (cites:,). ## Feedback, winding, and amplifier matching Feedback is an absolute single-turn SinCos encoder on the Hiperface protocol, so the SH32052P01A1000 pairs natively with servo drives that speak Hiperface for absolute position — no battery backup module or incremental-to-SinCos translator card is needed between motor and drive (cites:). The winding reads 0.3 Ohm with 8.2 mH of stator inductance and a torque constant of 2.58 N.m/A at the 120 °C copper-hot reference — the latter is the number to use when translating motor-side current into shaft torque, since the constant is specified at the hot winding rather than at 25 °C (cites:,). Maximum current is 96.8 A Irms and the continuous stall current sits at 25.7 A — the amplifier's peak and continuous current brackets should land either side of those two numbers, with a back-EMF constant of 161 V/krpm at 20 °C bounding the top speed the drive can sustain without field weakening (cites:,). ## Mechanical fit, shaft load, and panel-side wiring Mounting is an international standard flange on a 205 mm motor flange with a 180 mm centring collar taken to 4 mm depth and four 14 mm mounting holes — the package fits the common 205 mm servo footprint used across machine-tool and packaging machinery retrofits (cites:,). Power and feedback terminate through a rotatable right-angled connector or a straight connector option, so the cabinet exit can be rotated to keep the cable bend radius inside the manufacturer's minimum without re-ordering the motor (cites:,). ## Ingress protection and the production read The motor body carries IP65 to IEC 60034-5 and the shaft bushing carries IP65 with IP54 retained when the seal ring is omitted — that is the rating set for washdown-adjacent zones and outdoor cabinets, but not for submerged service (cites:).","metaTitle":"SH32052P01A1000 SH3 servo motor, 61.6 N.m, 7900 W","metaDescription":"Schneider SH32052P01A1000 SH3 series AC servo motor, three-phase, 7900 W continuous, IP65, Hiperface SinCos feedback. Quoted to order against the BOM.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"15.9 in (405 mm)","Shaft end":"Smooth shaft","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"Without","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"129 kg.cm²","Nominal torque":"545.2 lbf.in (61.6 N.m) 115 V single phase 495.6 lbf.in (56 N.m) 230 V single phase 337.2 lbf.in (38.1 N.m) 400 V three phase 251.4 lbf.in (28.4 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.58 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"7900 W","Mounting Support":"International standard flange","Sizing reference":"SH32052P","Back emf constant":"161 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"1947.2 lbf.in (220 N.m) 115...480 V three phase","Stator inductance":"8.2 mH","Stator resistance":"0.3 Ohm","Maximum current Irms":"96.8 A","Nominal output power":"3230 W 115 V single phase 5860 W 230 V single phase 7980 W 400 V three phase 7140 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"574.4 lbf.in (64.9 N.m) 115...480 V three phase","IP degree of protection":"IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5 IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"4200 N 1000 rpm 3330 N 2000 rpm 2910 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"25.7 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":null,"sourceUrl":"https://www.se.com/nl/en/product/SH32052P01A1000/sh3-servomotor-205mm-2-stacks-smooth-shaft-sincos-singleturn-128-no-brake-straight-ip54-65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH32052P01A1000/alternatives.json"},"ai":{"faq":[{"question":"What compliance documentation does the brand provide for the SH32052P01A1000?","answer":"The IP rating is documented to IEC 60034-5 at IP65 motor and IP65 shaft bushing, which is the only conformity declaration carried in the spec record (cites:)."},{"question":"What is the SH32052P01A1000's listed phase and length on this component line?","answer":"The motor is three phase at the network level with a 405 mm overall length (cites:,)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32052P01A1000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32052P01A1000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}