{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32052P02A1100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32052P02A1100","canonicalUrl":"https://aoctrl.com/schneider/SH32052P02A1100","factsUrl":"https://aoctrl.com/api/mcp/products/SH32052P02A1100","rawCanonicalId":null},"summary":{"shortDescription":"SH32052P02A1100, SH3 series three-phase servo motor, 5-pole, 7900 W continuous power, IP65, absolute multiturn SinCos Hiperface encoder, 205 mm flange, smooth shaft.","salesMarkdown":"## Motor ratings across supply voltages The SH32052P02A1100 delivers 61.6 Nm nominal torque at 500 rpm on 115 V single-phase supply, 56 Nm at 1000 rpm on 230 V single-phase, 38.1 Nm at 2000 rpm on 400 V three-phase, and 28.4 Nm at 2400 rpm on 480 V three-phase — the speed-torque envelope shifts with the available line voltage, so drive sizing must reference the actual supply at the installation point. Nominal output power follows the same pattern: 3230 W at 115 V single-phase, 5860 W at 230 V single-phase, 7980 W at 400 V three-phase, and 7140 W at 480 V three-phase. Continuous power is listed at 7900 W, which aligns with the 400 V three-phase rating. ## Feedback and environmental sealing The absolute multiturn SinCos Hiperface encoder provides position feedback without a home cycle on power-up — the multiturn count tracks absolute position across 4096 revolutions, which matters for applications where the machine must resume from the last known position after a power loss. IP65 protection per IEC 60034-5 applies to both the motor body and the shaft bushing — the seal at the shaft exit is the wet-end barrier, so the motor withstands washdown in food, beverage, or outdoor installations without an additional cover. ## Peak and continuous current limits Maximum current Irms is 96.8 A, and the same figure applies as the 3-second peak output current — the drive must supply this peak for acceleration and deceleration transients. Continuous stall current is 25.7 A, which sets the thermal baseline for holding torque applications. Peak stall torque reaches 220 Nm across the 115-480 V three-phase range, while continuous stall torque is 64.9 Nm — the ratio between peak and continuous stall torque is about 3.4:1, typical for servo motors handling high-inertia loads during acceleration. ## Mechanical interface and mounting The motor uses an international standard flange with a 205 mm flange size, 180 mm centring collar diameter, and 14 mm mounting holes — this matches common servo motor mounting patterns for direct coupling to machine frames or gearboxes. Shaft diameter is 1.5 in (38 mm) with a smooth shaft end and 3.1 in (80 mm) shaft length — the smooth shaft accepts a keyless clamping hub or a keyway-mount coupling. Maximum radial force is 4200 N at 1000 rpm, derating to 2910 N at 3000 rpm, which governs belt/pulley or direct-coupling bearing life.","metaTitle":"SH32052P02A1100 servo motor, 5-pole, 7900 W, IP65","metaDescription":"SH32052P02A1100 three-phase servo motor, 7900 W continuous, IP65, absolute multiturn Hiperface encoder. Active production — quoted to order against BOM.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH32052P02A1100","Length":"15.9 in (405 mm)","Inertia":"0.0 kg.cm² of brake 129.0 kg.cm² of motor","Category":"US1PC5218359","Shaft end":"Smooth shaft","description":"SH3 servomotor, 205mm, 2 stacks, smooth Shaft, SinCos Multiturn 128, no Brake, straight, IP65/65","Encoder type":"Absolute multiturn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"Without","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"129 kg.cm²","Nominal torque":"545.2 lbf.in (61.6 N.m) 115 V single phase 495.6 lbf.in (56 N.m) 230 V single phase 337.2 lbf.in (38.1 N.m) 400 V three phase 251.4 lbf.in (28.4 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.52 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"7900 W","Mounting Support":"International standard flange","Sizing reference":"SH32052P","Back emf constant":"161 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"1947.2 lbf.in (220 N.m) 115...480 V three phase","Stator inductance":"2.95 mH","Stator resistance":"0.3 Ohm","Maximum current Irms":"96.8 A","Nominal output power":"3230 W 115 V single phase 5860 W 230 V single phase 7980 W 400 V three phase 7140 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Output current 3s peak":"96.8 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"574.4 lbf.in (64.9 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"4200 N 1000 rpm 3330 N 2000 rpm 2910 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"25.7 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$7,605.00","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/47841b82bf8dee72c99beea20d3bc8f8.pdf","sourceUrl":"https://www.se.com/ie/en/product/SH32052P02A1100/sh3-servomotor-205mm-2-stacks-smooth-shaft-sincos-multiturn-128-no-brake-straight-ip65-65/"},"ai":{"faq":[{"question":"What is SH32052P02A1100's listed phase and length?","answer":"The motor is a three-phase design with an overall length of 15.9 in (405 mm). The shaft length is 3.1 in (80 mm)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32052P02A1100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32052P02A1100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-08-11T15:51:03.652Z","lastPublished":"2026-08-11T15:51:03.652Z","indexable":true}}