{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32052P11F1000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32052P11F1000","canonicalUrl":"https://aoctrl.com/schneider/SH32052P11F1000","factsUrl":"https://aoctrl.com/api/mcp/products/SH32052P11F1000","rawCanonicalId":null},"summary":{"shortDescription":"SH3 series servo motor, SH32052P11F1000, 7.9 kW continuous power, 2000 rpm nominal at 400 V three-phase, 61.6 Nm nominal torque, 80 Nm holding brake, IP65, absolute single-turn SinCos Hiperface encoder, 38 mm shaft with parallel key.","salesMarkdown":"## 7.9 kW continuous, 2000 rpm at 400 V three-phase The SH32052P11F1000 is a 7.9 kW continuous power servo motor from the SH3 series, delivering 2000 rpm nominal speed when fed from a 400 V three-phase drive. At 480 V three-phase it runs at 2400 rpm, and at 230 V single-phase it delivers 1000 rpm — the speed follows the applied voltage linearly per the back EMF constant of 161 V/krpm at 20°C. Nominal torque is 61.6 Nm at 115 V single-phase, dropping to 38.1 Nm at 400 V three-phase and 28.4 Nm at 480 V three-phase — the torque curve shifts with the available current from the drive. Peak stall torque reaches 220 Nm across the 115...480 V three-phase range, giving a 3.6× overload margin for acceleration and emergency stops. ## Absolute encoder, holding brake, IP65 — what each means for fit The absolute single-turn SinCos Hiperface encoder reports position at power-up without a homing cycle — critical for applications where the machine must resume from the last known position after a power loss. Single-turn means it tracks one revolution; multi-turn applications need an external battery-backed counter or a multi-turn encoder variant. IP65 on the motor body and shaft bushing means the winding and bearings are protected against dust ingress and low-pressure water jets — suitable for washdown areas and dusty production floors. The IP54 rating on the shaft bushing without the shaft seal ring is a fallback; the IP65 rating applies when the seal ring is fitted, which is the standard configuration for food and beverage or wet machining environments. The 5-pole design gives a lower cogging torque ripple than a standard 4-pole motor, which matters for contouring and surface-finish applications where torque ripple shows up as velocity ripple. Stator inductance is 2.95 mH and resistance is 0.3 Ω — these set the current-loop tuning parameters in the drive; a low-inductance motor like this needs a higher PWM frequency to keep current ripple within the drive's thermal limits. ## Mechanical interface — flange, shaft, and connector The motor mounts on an international standard flange with a 205 mm pilot diameter and a 4 mm centering collar depth. Four 14 mm mounting holes on the flange bolt circle — the bolt pattern matches standard IEC B5 flanges in this frame size. The 38 mm shaft extends 80 mm with a parallel key 10 mm wide — a standard metric keyway for coupling or pulley mounting. Maximum radial force at the shaft end is 4200 N at 1000 rpm, dropping to 2910 N at 3000 rpm; the bearing life follows the cube of the radial load, so a coupling that misaligns by even 0.1 mm reduces the service life significantly. The electrical connection is a rotatable right-angle connector or a straight connector — the rotatable version lets the cable exit in any of four orientations, which simplifies routing in tight cabinets. The connector carries the power, encoder, and brake wires; the brake wires are separate from the motor power leads to avoid induced voltage spikes on the brake coil.","metaTitle":"SH32052P11F1000 servo motor, 7.9 kW, 2000 rpm, 61.6 Nm, IP65","metaDescription":"SH32052P11F1000 servo motor, 7.9 kW continuous, 2000 rpm at 400 V three-phase, 61.6 Nm nominal torque, IP65, absolute single-turn SinCos Hiperface encoder","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH32052P11F1000","Length":"17.9 in (454.5 mm)","Inertia":"16.0 kg.cm² of brake 129.0 kg.cm² of motor","Category":"US1PC5218359","Key width":"0.4 in (10 mm)","Shaft end":"Parallel key","description":"SH3 servomotor, 205mm, 2 stacks, keyed Shaft, SinCos Singleturn 128, Brake, straight, IP54/65","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"With","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"145 kg.cm²","Holding torque":"708.06 lbf.in (80 N.m)","Nominal torque":"545.2 lbf.in (61.6 N.m) 115 V single phase 495.6 lbf.in (56 N.m) 230 V single phase 337.2 lbf.in (38.1 N.m) 400 V three phase 251.4 lbf.in (28.4 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.52 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"7900 W","Mounting Support":"International standard flange","Sizing reference":"SH32052P","Back emf constant":"161 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"1947.2 lbf.in (220 N.m) 115...480 V three phase","Stator inductance":"2.95 mH","Stator resistance":"0.3 Ohm","Maximum current Irms":"96.8 A","Nominal output power":"3230 W 115 V single phase 5860 W 230 V single phase 7980 W 400 V three phase 7140 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Output current 3s peak":"96.8 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"574.4 lbf.in (64.9 N.m) 115...480 V three phase","IP degree of protection":"IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5 IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"4200 N 1000 rpm 3330 N 2000 rpm 2910 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"25.7 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$7,775.00","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/47841b82bf8dee72c99beea20d3bc8f8.pdf","sourceUrl":"https://www.se.com/nl/en/product/SH32052P11F1000/sh3-servomotor-205mm-2-stacks-keyed-shaft-sincos-singleturn-128-brake-straight-ip54-65/"},"ai":{"faq":[{"question":"What is the nominal torque of SH32052P11F1000 at 400 V three-phase?","answer":"At 400 V three-phase the nominal torque is 38.1 Nm (337.2 lbf.in). At 480 V three-phase it drops to 28.4 Nm (251.4 lbf.in), and at 115 V single-phase it reaches 61.6 Nm (545.2 lbf.in). The torque varies with the applied voltage and phase configuration."},{"question":"What encoder type does SH32052P11F1000 use?","answer":"It uses an absolute single-turn SinCos Hiperface encoder. This provides position feedback at power-up without a homing sequence, and the SinCos analog tracks give high-resolution velocity feedback for the drive's current loop."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32052P11F1000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32052P11F1000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}