{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32052P11F2200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32052P11F2200","canonicalUrl":"https://aoctrl.com/schneider/SH32052P11F2200","factsUrl":"https://aoctrl.com/api/mcp/products/SH32052P11F2200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3.....P series three-phase servo motor, SH32052P11F2200, 80 N.m holding torque, 7900 W continuous power, IP65/IP67 sealed, SinCos Hiperface absolute single-turn encoder.","salesMarkdown":"## Torque and speed across the supply rail The SH32052P11F2200: Nominal speed scales with the drive bus: 500 rpm on 115 V single-phase, 1000 rpm on 230 V single-phase, 2000 rpm on 400 V three-phase, and 2400 rpm on 480 V three-phase, which is the figure a panel designer uses to set the drive's speed-command ceiling for each install. Nominal torque follows the inverse — 545.2 lbf.in (61.6 N.m) at 115 V, 495.6 lbf.in (56 N.m) at 230 V, 337.2 lbf.in (38.1 N.m) at 400 V, and 251.4 lbf.in (28.4 N.m) at 480 V — so a 400 V three-phase pairing gives the practical working point of 7980 W nominal output power, while stepping up to 480 V trades torque for top-end speed. Continuous stall torque is 574.4 lbf.in (64.9 N.m) at 25.7 A across 115...480 V, which is the steady-state figure the drive's current loop has to hold when the rotor is commanded to a fixed position — i.e. the sizing basis for the servo amplifier's continuous-current rating. ## SinCos Hiperface feedback and electrical interface The electrical interface is a rotatable right-angled connector, letting the cable exit in any of four directions after the motor is bolted down — important in cabinets where the cable gland lands on a fixed side and the motor can be mounted in either orientation. ## IP65/IP67 sealing and thermal envelope Winding thermal limit is 266 °F (130 °C) copper-hot across 5 motor poles, with cooling by natural convection only — derating starts above the ambient curve the manufacturer publishes, and panel integrators typically budget 10–15 % continuous-torque margin when the motor is mounted inside an enclosure without assisted airflow. ## Shaft, flange, and shaft-load envelope Shaft end is a 1.5 in (38 mm) parallel-key shaft with a 0.4 in (10 mm) key, 3.1 in (80 mm) long, mounted on a 205 mm flange with a 180 mm centring collar at 4 mm depth and four 0.6 in (14 mm) mounting holes — the standard IEC mounting footprint that drops onto any gearbox or coupling rated for the torque class. ## Sourcing posture for the SH32052P11F2200 Pricing and availability are confirmed against an RFQ: this code is quoted to order on the production BOM, with current lead time and volume pricing returned at quote time rather than posted as a list number.","metaTitle":"SH32052P11F2200 Servo Motor, 80 N.m, 7900 W, IP65","metaDescription":"SH32052P11F2200 three-phase servo motor, 80 N.m holding torque, 7900 W continuous, IP65/IP67 sealed, SinCos Hiperface feedback. Quoted to order against an RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"17.9 in (454.5 mm)","Category":"US1PC5218359","Key width":"0.4 in (10 mm)","Shaft end":"Parallel key","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"With","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"145 kg.cm²","Holding torque":"708.06 lbf.in (80 N.m)","Nominal torque":"545.2 lbf.in (61.6 N.m) 115 V single phase 495.6 lbf.in (56 N.m) 230 V single phase 337.2 lbf.in (38.1 N.m) 400 V three phase 251.4 lbf.in (28.4 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.58 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"7900 W","Mounting Support":"International standard flange","Sizing reference":"SH32052P","Back emf constant":"161 V/krpm 68 °F (20 °C)","Device short name":"SH3.....P","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"1947.2 lbf.in (220 N.m) 115...480 V three phase","Stator inductance":"8.2 mH","Stator resistance":"0.3 Ohm","Maximum current Irms":"96.8 A","Nominal output power":"3230 W 115 V single phase 5860 W 230 V single phase 7980 W 400 V three phase 7140 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"rotatable right angled connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"574.4 lbf.in (64.9 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"4200 N 1000 rpm 3330 N 2000 rpm 2910 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"25.7 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":null,"sourceUrl":"https://www.se.com/ca/en/product/SH32052P11F2200/servo-motor-sh3-205-649nmkeysinglebrake90âconn-ip65-ip673-8k-rpm/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH32052P11F2200/alternatives.json"},"ai":{"faq":[{"question":"What is the SH32052P11F2200's phase and how does it drive the working point?","answer":"Lower-voltage single-phase pairings deliver higher torque at lower speed; the 480 V three-phase pairing delivers 2400 rpm but only 251.4 lbf.in (28.4 N.m)."},{"question":"How long is the SH32052P11F2200 and what flange does it use?","answer":"Body length is 17.9 in (454.5 mm) on an 8.07 in (205 mm) international-standard flange with a 7.09 in (180 mm) centring collar — the standard IEC mounting footprint that bolts directly to a gearbox or planetary reducer in the same torque class."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32052P11F2200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32052P11F2200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}