{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32053P01F1000","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32053P01F1000","canonicalUrl":"https://aoctrl.com/schneider/SH32053P01F1000","factsUrl":"https://aoctrl.com/api/mcp/products/SH32053P01F1000","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 servo motor, SH32053P01F1000, 80 N.m holding torque, 10600 W continuous, 38 mm smooth shaft, Hiperface SinCos encoder, IP65, flange mount.","salesMarkdown":"## What this motor is and where it sits The SH32053P01F1000 is a three-phase AC servo motor from the SH3 series, sized to the SH32053P frame with an international-standard 205 mm flange, and shipped with a built-in holding brake so the shaft stays put when the drive is de-energised. Feedback is an absolute single-turn SinCos encoder on the Hiperface protocol, which pairs with the matching servo drive for commutation and position without a separate homing routine at power-up. ## Torque, speed, and the voltage-tap envelope Continuous torque varies by the bus voltage applied: 84.9 N.m at 115 V single phase, 74.4 N.m at 230 V single phase, 50.7 N.m at 400 V three phase, and 40.2 N.m at 480 V three phase — so the same frame delivers more torque at the lower taps where the drive cannot drive the back-EMF as hard, and trades torque for top speed as the bus climbs. Nominal speed follows the same curve in reverse: 500 rpm at 115 V single phase, 1000 rpm at 230 V single phase, 2000 rpm at 400 V three phase, and 2400 rpm at 480 V three phase, with a maximum mechanical speed of 3800 rpm regardless of bus voltage — that ceiling is the bearing limit, not an electrical one. Continuous power lines out at 10600 W (the 400 V three-phase tap), with 4450 W / 7790 W / 10620 W / 10100 W at the four operating points — so the spec sheet is best read as four separate torque-speed operating points, not a single flat curve. Peak stall torque reaches 330 N.m (2920.7 lbf.in) at the 115 to 480 V three-phase taps and continuous stall torque is 94.4 N.m — the peak figure is what the drive delivers during acceleration and deceleration, and it is the number that sizes the drive's current capacity. ## Winding electricals and thermal ceiling Stator resistance is 0.2 Ohm and stator inductance is 6.3 mH, with continuous stall current 33.2 A and a maximum Irms of 136.1 A — the drive must be capable of at least the Irms figure in transient duty, and the bus capacitors must absorb the regen from the 3800 rpm top speed on rapid stops. Cooling is natural convection with no fan, and the winding hot-spot ceiling is 130 °C — sealed cabinets or heat-soaked mounting surfaces push the motor toward the thermal limit faster than the equivalent fan-cooled frame, so cabinet airflow or a cold plate should be considered in the panel layout. ## Mechanical envelope and shaft loading Overall length is 21.2 in (538.5 mm), shaft diameter 1.5 in (38 mm), shaft length 3.1 in (80 mm), with a smooth shaft end — the 38 mm shaft accepts standard servo-grade couplings sized for the torque and the keyed / smooth choice should match the driven load. Maximum axial force Fa is 740 N, the centring collar is 180 mm in diameter with a 4 mm depth, and the mounting holes are 14 mm on the international-standard 205 mm flange — the flange pattern is the dimensional interface the panel builder matches to the gearbox or driven load. ## Ingress, poles, and connector options The motor has 5 poles and the electrical connection is offered as a rotatable right-angled connector or a straight connector — the rotatable variant simplifies cable routing inside confined cabinets where the bend radius would otherwise stress the cable. ## Sourcing posture Pin-compatible alternates inside the same SH3 series would be the framing if a like-for-like substitute is needed — the SH32053P family is the sizing reference carried on this order code. Send the quantity and the drive pairing; the BOM line gets sourced and quoted back against the RFQ rather than walked through the datasheet here.","metaTitle":"SH32053P01F1000 servo motor, 80 N.m, IP65, Hiperface","metaDescription":"SH32053P01F1000 SH3 servo motor: 80 N.m holding, 10600 W continuous, IP65, Hiperface SinCos encoder, quoted to order against an RFQ.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Obsolete","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","Length":"21.2 in (538.5 mm)","Shaft end":"Smooth shaft","Encoder type":"Absolute single turn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"With","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"206 kg.cm²","Holding torque":"708.06 lbf.in (80 N.m)","Nominal torque":"751.4 lbf.in (84.9 N.m) 115 V single phase 658.5 lbf.in (74.4 N.m) 230 V single phase 448.7 lbf.in (50.7 N.m) 400 V three phase 355.8 lbf.in (40.2 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.76 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"10600 W","Mounting Support":"International standard flange","Sizing reference":"SH32053P","Back emf constant":"172 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"2920.7 lbf.in (330 N.m) 115...480 V three phase","Stator inductance":"6.3 mH","Stator resistance":"0.2 Ohm","Maximum current Irms":"136.1 A","Nominal output power":"4450 W 115 V single phase 7790 W 230 V single phase 10620 W 400 V three phase 10100 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"835.5 lbf.in (94.4 N.m) 115...480 V three phase","IP degree of protection":"IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5 IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"4500 N 1000 rpm 3570 N 2000 rpm 3120 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"33.2 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"priceTiers":null},"links":{"datasheetUrl":null,"sourceUrl":"https://www.se.com/us/en/product/SH32053P01F1000/sh3-servomotor-205mm-3-stacks-smooth-shaft-sincos-singleturn-128-brake-straight-ip54-65/","alternativesUrl":"https://aoctrl.com/api/mcp/products/SH32053P01F1000/alternatives.json"},"ai":{"faq":[{"question":"What is SH32053P01F1000's listed phase on this component line?","answer":"SH32053P01F1000 is a three-phase AC servo motor — both the phase field and the network number of phases entry on the spec sheet confirm three phases."},{"question":"What is the overall length of SH32053P01F1000?","answer":"The motor body is 21.2 in (538.5 mm) long end to end, with a 38 mm smooth shaft and an 80 mm shaft length, and an international-standard 205 mm flange on the mounting face."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32053P01F1000","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32053P01F1000 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-09-02T08:15:54.622Z","lastPublished":"2026-09-02T08:15:54.622Z","indexable":true}}