{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32053P02A1200","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32053P02A1200","canonicalUrl":"https://aoctrl.com/schneider/SH32053P02A1200","factsUrl":"https://aoctrl.com/api/mcp/products/SH32053P02A1200","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3 series three-phase servo motor, 10600 W continuous, IP65, 205 mm flange, absolute multiturn SinCos Hiperface encoder.","salesMarkdown":"## What kind of axis does this motor actually drive? The SH32053P02A1200 is a Schneider Electric SH3 series three-phase servo motor sized at 10600 W continuous, with a 205 mm international-standard flange and an absolute multiturn SinCos Hiperface encoder on a smooth 38 mm shaft — the configuration most integrators reach for on a high-inertia indexing or web-tension axis where absolute position retention survives a power cycle. ## Why the four-row nominal table matters more than the headline wattage Continuous power varies with the bus the drive is run from — 4450 W at 115 V single phase, 7790 W at 230 V single phase, 10620 W at 400 V three phase, 10100 W at 480 V three phase — which is why the 10600 W figure on the spec row is the three-phase 400 V operating point, not a universal number. Nominal torque follows the same pattern and inverts with voltage: 84.9 N·m at 115 V single phase drops to 40.2 N·m at 480 V three phase, because the higher nominal speeds (2000 rpm at 400 V, 2400 rpm at 480 V) trade torque for top-end velocity on the constant-power region. Back EMF constant of 172 V/krpm at 20 °C and a torque constant of 2.84 N·m/A at 120 °C copper temperature are the two numbers the drive commissioning engineer cross-checks against the amplifier's bus voltage and current-loop gain before the first saturation test. ## Peak versus continuous — which rating actually governs sizing Peak stall torque reaches 330 N·m across the 115–480 V range, against 94.4 N·m continuous stall torque at the same envelope — roughly 3.5× overload headroom for short acceleration steps, the figure the sizing engineer uses for the worst-case move profile. Peak current Irms of 136.1 A and continuous stall current of 33.2 A set the same ratio on the electrical side; the drive's peak-current window must be sized to deliver the 3-second peak without tripping, while the root-mean-square current over the duty cycle must stay below the 33.2 A continuous figure to avoid thermal cutback. Stator resistance 0.2 Ohm and stator inductance 2.05 mH are the loop-tuning inputs the current regulator uses to set bandwidth — the low L/R ratio (~10 ms electrical time constant) is typical of this frame size and lets the drive push the velocity loop higher than a high-inductance servo. ## Where the SH3 fits in a real cabinet — flange, shaft, sealing Mounting is the international-standard flange pattern with a 205 mm motor flange, 180 mm centring collar with 4 mm depth, and 14 mm mounting holes — drop-in for the standard 200 mm-frame machine-builder baseplate. Overall length is 489 mm with a 80 mm shaft extension of 38 mm diameter, so the mechanical designer has to budget the cantilever load against the published radial/axial limits: 4500 N radial at 1000 rpm, derating linearly to 3120 N at 3000 rpm, with 740 N maximum axial force. Ingress protection is IP65 on the motor body and shaft bushing plus IP67 on the housing, all per IEC 60034-5 — adequate for a washdown-adjacent food line or outdoor cell, and the cooling method is natural convection with a 130 °C copper-hot thermal limit, so no external fan or blower duct is needed in the cabinet layout.","metaTitle":"SH32053P02A1200 SH3 Servo Motor, 10600 W, IP65","metaDescription":"Schneider Electric SH3 servo motor SH32053P02A1200, three-phase, 10600 W continuous, IP65, absolute SinCos Hiperface encoder. Quoted to order against the BOM.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH32053P02A1200","Length":"19.3 in (489 mm)","Inertia":"0.0 kg.cm² of brake 190.0 kg.cm² of motor","Category":"US1PC5218359","Shaft end":"Smooth shaft","description":"SH3 servomotor, 205mm, 3 stacks, smooth Shaft, SinCos Multiturn 128, no Brake, straight, IP65/67","Encoder type":"Absolute multiturn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"Without","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"190 kg.cm²","Nominal torque":"751.4 lbf.in (84.9 N.m) 115 V single phase 658.5 lbf.in (74.4 N.m) 230 V single phase 448.7 lbf.in (50.7 N.m) 400 V three phase 355.8 lbf.in (40.2 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.84 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"10600 W","Mounting Support":"International standard flange","Sizing reference":"SH32053P","Back emf constant":"172 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"2920.7 lbf.in (330 N.m) 115...480 V three phase","Stator inductance":"2.05 mH","Stator resistance":"0.2 Ohm","Maximum current Irms":"136.1 A","Nominal output power":"4450 W 115 V single phase 7790 W 230 V single phase 10620 W 400 V three phase 10100 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Straight connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Output current 3s peak":"136.1 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"835.5 lbf.in (94.4 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5","Maximum radial force Fr":"4500 N 1000 rpm 3570 N 2000 rpm 3120 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"33.2 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":null,"stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"{'url': 'https://www.se.com/us/en/product/download-pdf/SH32053P02A1200?filename=Schneider+Electric_Lexium-52-Motors_SH32053P02A1200.pdf', 'path_name': '07f15fe37eee855334d0d88be24a2680.pdf', 'path_url': 'https://s3.lax.sharktech.net/viassion/datasheets/schneider_electric/07f15fe37eee855334d0d88be24a2680.pdf', 'status': 1}","sourceUrl":"https://www.se.com/nl/en/product/SH32053P02A1200/sh3-servomotor-205mm-3-stacks-smooth-shaft-sincos-multiturn-128-no-brake-straight-ip65-67/"},"ai":{"faq":[{"question":"What is the listed phase on the SH32053P02A1200?","answer":"Three phase. The motor is rated across a wider supply envelope — 115 V and 230 V single-phase as well as 400 V and 480 V three-phase — but the canonical configuration is three-phase, with the 10600 W continuous power figure tied to the 400 V three-phase operating point."},{"question":"What is the overall length of the SH32053P02A1200?","answer":"489 mm (19.3 in), with a 205 mm flange and an 80 mm shaft extension of 38 mm diameter. The mechanical designer uses the radial-load derating curve (4500 N at 1000 rpm down to 3120 N at 3000 rpm) to confirm the cantilevered gearbox or pulley stays within the published envelope at top speed."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32053P02A1200","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32053P02A1200 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}