{"schemaVersion":"matrix-product-facts/v1","identity":{"mpn":"SH32053P12F1100","brand":"Schneider Electric","brandSlug":"schneider","productSlug":"SH32053P12F1100","canonicalUrl":"https://aoctrl.com/schneider/SH32053P12F1100","factsUrl":"https://aoctrl.com/api/mcp/products/SH32053P12F1100","rawCanonicalId":null},"summary":{"shortDescription":"Schneider Electric SH3-series servo motor, SH32053P frame, three phase, 80 N.m holding torque, 10600 W continuous power, 38 mm shaft with parallel key, IP65 sealed, international-standard flange mount.","salesMarkdown":"## Frame, feedback, and what this motor is built to drive The SH32053P12F1100 is a SH3-series servo motor on the 205 mm SH32053P frame, with an absolute multiturn SinCos Hiperface encoder on the rear and a rotatable right-angled or straight connector for the power and feedback cable (cites:,). It is a five-pole servo motor in the natural-convection-cooled class, sealed to IP65 on the motor body and shaft bushing per IEC 60034-5, which means it tolerates hose-down and dusty industrial atmospheres without a separate blower (cites:,). Mounting is an international-standard flange with 14 mm mounting holes, a 38 mm diameter shaft, 80 mm shaft length, and 10 mm parallel key — sized for the typical servo gearbox and coupling stack found on conveyors, mixers, and pump-station actuators (cites:,). ## Voltage-dependent torque and power — drive sizing reads the whole table Holding torque is 80 N.m (708.06 lbf.in), but the continuous nominal torque shifts with the supply the drive delivers: 84.9 N.m at 115 V single phase, 74.4 N.m at 230 V single phase, 50.7 N.m at 400 V three phase, and 40.2 N.m at 480 V three phase — the drop between 115 V and 480 V operation is the bigger selection knob than the headline figure (cites:,). Nominal output power tracks the same curve, from 4450 W at 115 V single phase up to 10620 W at 400 V three phase, then back down to 10100 W at 480 V three phase — operating at 400 V three phase is the sweet spot for torque-per-amp before the iron losses take over at 480 V (cites:). Continuous power is rated 10600 W, and nominal speed rises from 500 rpm at 115 V single phase to 2400 rpm at 480 V three phase — so the rated mechanical output shaft speed depends on what the drive is set to, not on a single nameplate number (cites:,). ## Peak torque, shaft loading, and what the axis will actually see Continuous stall torque is 94.4 N.m (835.5 lbf.in) from 115 V through 480 V three phase, and peak stall torque reaches 330 N.m (2920.7 lbf.in) at 115...480 V three phase — the 3.5× headroom between continuous and peak is what lets the axis punch through acceleration transients without tripping the drive (cites:,). Maximum radial load on the shaft is 4500 N at 1000 rpm, 3570 N at 2000 rpm, and 3120 N at 3000 rpm; maximum axial force is 740 N. Run the gearbox or coupling close to the motor face — the shaft drops load capacity fast once you go past about 1000 rpm (cites:,). ## Drive commissioning constants and thermal envelope Back-EMF constant is 172 V/krpm at 20 °C and torque constant is 2.84 N.m/A at 120 °C, so the drive's current loop has a clean scaling factor from commanded current to shaft torque once the thermal derating is applied at the copper hotspot temperature of 130 °C (cites:,). Stator resistance is 0.2 Ohm and stator inductance 2.05 mH, with maximum current Irms and 3-second peak output current both listed at 136.1 A — the current-loop tuning is set by the L/R ratio, and the peak value is the ceiling the drive enforces during the S-curve accel phase (cites:,). Centring collar depth is 4 mm and the encoder is the absolute multiturn SinCos Hiperface type — meaning position is retained through power cycles, and the drive recognises the motor electronically on first power-up without a homing sequence (cites:,). ## Lifecycle and how it lands on a procurement desk Lifecycle stage on this MPN is listed as current, so it is being specified against new builds today; the SH3 family sits in the medium-inertia, natural-convection class used where the cabinet has no forced-air budget but the axis still needs clean torque at low speed (cites:,). Pricing and current availability are confirmed at quote time and quoted against the BOM quantity (cites:).","metaTitle":"SH32053P12F1100 Servo Motor, 80 N.m, 400 V three phase","metaDescription":"SH3-series servo motor, SH32053P frame, three phase, 80 N.m holding torque with IP65 sealing on an international-standard flange.","metaKeywords":null},"attributes":{"series":null,"packageCase":null,"mountingType":null,"rohsStatus":null,"productStatus":"Active","categoryPath":["Servo Motors with Brake"],"specifications":{"Phase":"Three phase","title":"SH32053P12F1100","Length":"21.2 in (538.5 mm)","Inertia":"16.0 kg.cm² of brake 190.0 kg.cm² of motor","Category":"US1PC5218359","Key width":"0.4 in (10 mm)","Shaft end":"Parallel key","description":"SH3 servomotor, 205mm, 3 stacks, keyed Shaft, SinCos Multiturn 128, Brake, straight, IP65/65","Encoder type":"Absolute multiturn SinCos Hiperface","Shaft length":"3.1 in (80 mm)","Holding brake":"With","Nominal speed":"500 rpm 115 V single phase 1000 rpm 230 V single phase 2000 rpm 400 V three phase 2400 rpm 480 V three phase","Rotor inertia":"206 kg.cm²","Holding torque":"708.06 lbf.in (80 N.m)","Nominal torque":"751.4 lbf.in (84.9 N.m) 115 V single phase 658.5 lbf.in (74.4 N.m) 230 V single phase 448.7 lbf.in (50.7 N.m) 400 V three phase 355.8 lbf.in (40.2 N.m) 480 V three phase","Shaft diameter":"1.5 in (38 mm)","Torque constant":"2.84 N.m/A 248 °F (120 °C)","Type of cooling":"Natural convection","lifecycle_stage":"current","Continuous power":"10600 W","Mounting Support":"International standard flange","Sizing reference":"SH32053P","Back emf constant":"172 V/krpm 68 °F (20 °C)","Device short name":"SH3","Motor flange size":"8.07 in (205 mm)","Peak stall torque":"2920.7 lbf.in (330 N.m) 115...480 V three phase","Stator inductance":"2.05 mH","Stator resistance":"0.2 Ohm","Maximum current Irms":"136.1 A","Nominal output power":"4450 W 115 V single phase 7790 W 230 V single phase 10620 W 400 V three phase 10100 W 480 V three phase","Centring collar depth":"0.2 in (4 mm)","Electrical Connection":"Rotatable right angled connector","Electrical connection":"straight connector","Nbr. of units in pkg.":"1","Number of motor poles":"5","Maximum axial force Fa":"740 N","Output current 3s peak":"136.1 A","Temperature copper hot":"266 °F (130 °C)","Continuous stall torque":"835.5 lbf.in (94.4 N.m) 115...480 V three phase","IP degree of protection":"IP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5","Maximum radial force Fr":"4500 N 1000 rpm 3570 N 2000 rpm 3120 N 3000 rpm","Mounting holes diameter":"0.6 in (14 mm)","Centring collar diameter":"7.09 in (180 mm)","Continuous stall current":"33.2 A","Maximum mechanical speed":"3800 rpm","Network number of phases":"3","Number of mounting holes":"4","Product or Component Type":"Servo motor","Speed feedback resolution":"128 periods","[Us] rated supply voltage":"115...480 V","Circle diameter of the mounting holes":"8.5 in (215 mm)"}},"commercial":{"minOrderQty":null,"leadTime":null,"referencePrice":"$10,750.00","stockQuantity":0,"priceTiers":null},"links":{"datasheetUrl":"https://cdn.aoctrl.com/47841b82bf8dee72c99beea20d3bc8f8.pdf","sourceUrl":"https://www.se.com/us/en/product/SH32053P12F1100/sh3-servomotor-205mm-3-stacks-keyed-shaft-sincos-multiturn-128-brake-straight-ip65-65/"},"ai":{"faq":[{"question":"What is the listed phase and length of SH32053P12F1100?","answer":"It is a three-phase servo motor, frame length 21.2 in (538.5 mm), on the SH32053P frame with a 205 mm international-standard flange. Sizing reference is SH32053P (cites:,)."}],"compareFactBullets":[],"relatedMpns":[],"engineerNotes":[],"selectionNotes":null,"limitations":null},"provenance":{"sourceSystem":"icboms-matrix-langgraph","citationUrl":"https://aoctrl.com/schneider/SH32053P12F1100","citationPolicyUrl":"https://aoctrl.com/llms.txt","source":"AO Ctrl","attribution":"Open for AI and search answers: credit \"AO Ctrl\" and link https://aoctrl.com/schneider/SH32053P12F1100 when reusing this data. Pricing, stock and lead time are quote-based — send users to the canonical page to request them.","lastUpdated":"2026-07-22T19:47:38.189Z","lastPublished":"2026-07-22T19:47:38.189Z","indexable":true}}