Schneider Electric NTSAHO0212H
MPNNTSAHO0212H
Active
Analog Output Module, 2 Isolated Out, Current, HART, Hardened, Modicon Edge I/O NTS
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026
Specifications
| Parameter | Value |
|---|---|
| Type of cable | Shielded cable |
| Range of product | Modicon Edge I/O NTS |
| Power supply type | Bus power from power supply bus (24 Vdc) Field power from power supply field (24 Vdc) |
| Analogue output type | Current 4...20 mA |
| Output protection type | 30V over voltage for current output |
| Product or component type | Analog HART output module |
| Rated operational voltage limits | 20.4...28.8 V DC |
| Typical current consumption | 37.4 mA 24 V DC on the Bus current 34.1 mA 24 V DC on the internal field current minimum 82.5 mA 24 V DC on the internal field current maximum |
| Power dissipation in | 2.3 W maximum at 24 V DC |
| Isolation between field power and bus | 1500 V AC |
| IP degree of protection | IP20 |
| Mounting support | base |
All specifications
| Parameter | Value |
|---|---|
| Maximum cable distance between devices | Shielded cable <3280.8 ft (1000 m) current input |
| Response time on output | 500 µs at 8750 Ohm per module (HART disabled) |
| Pollution degree | 2 |
| Shock resistance | 15 g 11 ms with and without accessory) |
| Relative humidity | 5...95 % without condensation |
| Operating altitude | 0...6561.68 ft (0...2000 m) 2000...5000 m with derating |
| Vibration resistance | 1 g without accessory 2 g with accessory |
| Depth | 2.7 in (69 mm) |
| Width | 1.2 in (30 mm) |
| Height | 3.9 in (100 mm) |
| Housing colour | Grey |
| Product weight | 0.174 lb(US) (0.079 kg) |
| Standards | EN/IEC 61131-2 EN 61010-2-201 UL 61010-2-201 IACS E10 EN/IEC 61000-6-5 EN/IEC 61850-3 EN/IEC 60079-0 EN 50155 EN 50121-4 EN 50121-5 |
| Marking | CE UKCA CULus RCM |
| Category | US1PC3318214 |
| Directives | 2014/30/EU - electromagnetic compatibility 2014/34/EU - ATEX directive 2014/35/EU |
| Non-linearity | <= 0.02 % FS current |
| HART tolerance | Yes |
| Operating mode | Asynchronous |
| Local signalling | 1 LED green module operating (RUN) 1 LED per channel green channel diagnostic 1 LED red module error (ERR) |
| Measurement error | <= 0.2 % FS - 40...70 °C |
| Output diagnostic | Underflow error per channel Overflow error per channel Broken wire error per channel Short circuit error per channel Hardware error per channel Calibration error per channel DAC power error per channel Internal field power supply error per channel |
| Temperature drift | ± 0.002 % FS/ °C |
| Device application | Industrial application in severe environment |
| Output wiring mode | 2 wires |
| Mandatory accessory | NTSXBA0200H base NTSXTB12_0_H terminal block |
| Load impedance ohmic | 750 Ohm current |
| Protective treatment | Conformal coating |
| Hot swapping fallback | Yes |
| Analogue output number | 2 |
| Isolation between channels | 530 V AC |
| Environmental characteristic | Gas resistant CX & GX combined C3 and G2 Salt spray resistant |
| Isolation between channels and bus | 1500 V AC |
| Ambient air temperature for storage | -40...185 °F (-40...85 °C) |
| Ambient air temperature for operation | 104...158 °F (40...70 °C) |
| Isolation between channels and field pwr | 1000 V AC |
MPN
NTSAHO0212H