Schneider Electric NTSDDO0802XK
MPNNTSDDO0802XK
Active
Discrete Output Module + Base, 8 Out, 24V DC, 500mA, Source, Protected, 1/2 Wires, Modicon Edge I/O NTS
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026
Specifications
| Parameter | Value |
|---|---|
| Range of product | Modicon Edge I/O NTS |
| Power supply type | Bus power from power supply bus (24 Vdc) Field power from power supply field (24 Vdc) |
| Output protection type | Transient voltage suppression per channel Short circuit protection per channel Overload/thermal protection per channel Reverse polarity protection per module |
| Product or component type | Discrete output module kit |
| Maximum voltage drop | <0.1 V per channel DC |
| Discrete output voltage | 24 V DC |
| Rated operational voltage limits | 20.4...28.8 V DC |
| Discrete output current | 0.5 A per channel 4 A per module |
| Maximum leakage current | 0.001 mA per channel |
| Typical current consumption | 33.6 mA 24 V DC on the Bus current 3.6 mA 24 V DC on the internal field current minimum 4004.3 mA 24 V DC on the internal field current maximum |
| Power dissipation in | 1.83 W maximum at 24 V DC |
| Discrete output frequency | 1 kHz for resistive load 0.5/LI² Hz for inductive load |
All specifications
| Parameter | Value |
|---|---|
| IP degree of protection | IP20 |
| Mounting support | Top hat type TH35-7.5 IEC 60715 Top hat type TH35-15 IEC 60715 |
| Response time on output | 90 µs maximum (turn on) 110 µs maximum (turn off) |
| Pollution degree | 2 |
| Shock resistance | 15 g 11 ms with and without accessory) |
| Relative humidity | 5...95 % without condensation |
| Operating altitude | 0...6561.68 ft (0...2000 m) without derating 2000...5000 m with derating |
| Vibration resistance | 1 g without accessory 2 g with accessory |
| Depth | 3.1 in (80 mm) |
| Width | 0.6 in (15 mm) |
| Height | 4.8 in (121 mm) |
| Housing colour | Grey |
| Standards | EN/IEC 61131-2 EN 61010-2-201 UL 61010-2-201 IACS E10 EN/IEC 61000-6-5, interface type 1 and type 2 EN/IEC 61850-3, location G EN/IEC 60079-0 EN 50155 EN 50121-4 EN 50121-5 |
| Marking | CE UKCA CULus RCM |
| Category | US1PC3318214 |
| Directives | 2014/30/EU - electromagnetic compatibility 2014/34/EU - ATEX directive 2014/35/EU |
| Operating mode | Synchronous/Isochronous |
| Kit composition | NTSDDO0802X module NTSXBA0200H base |
| Local signalling | 1 LED (green) for module operating (RUN) 1 LED per channel (green) for channel diagnostic 1 LED (red) for module error (ERR) |
| Output diagnostic | Power supply error per channel Over current error per channel |
| Device application | Industrial Application |
| Output wiring mode | 1 or 2 wires |
| Mandatory accessory | NTSXTB18_0_H terminal block |
| Discrete output logic | Positive logic (source) |
| Hot swapping fallback | Yes |
| Maximum tungsten load | <12 W |
| Discrete output number | 8 transistor |
| Paralleling of outputs | Yes for redundancy Yes for double current (maximum 2) |
| Group of output channels | 1 group |
| Environmental characteristic | Gas resistant C3 and G2 |
| Isolation between channels and bus | 1500 V AC |
| Ambient air temperature for storage | -40...185 °F (-40...85 °C) |
| Ambient air temperature for operation | -4...140 °F (-20...60 °C) |
| Isolation between channels and ground | 1500 V AC |
MPN
NTSDDO0802XK