Schneider ILE1R661PB1A6 — now discontinued, supplied from remaining surplus and broker stock.
| Parameter | Value |
|---|---|
| Motor type | Brushless DC motor |
| Network type | DC |
| Winding type | Medium speed of rotation and medium torque |
| Feedback type | BLDC encoder |
| Gear box type | Worm gear, 3 stages |
| Protection type | Safe torque off Overload of output voltage Short circuit of the output voltage |
| Type of cooling | Natural convection |
| Range of product | Lexium integrated drive |
| Input (output type) | 4 signals (each be used as input or output) |
| Product or component type | Motion integrated drive |
| Supply voltage limits | 18...40 V |
| Discrete output voltage | 23...25 V |
| Parameter | Value |
|---|---|
| Supply voltage | 36 V 24 V |
| Voltage state 0 guaranteed | -3...4.5 V |
| Voltage state 1 guaranteed | 15...30 V |
| Current consumption | 7000 mA peak 5500 mA maximum continuous |
| Discrete input current | 10 mA at 24 V on/STO_A safety input 3 mA at 24 V on/STO_B safety input 2 mA at 24 V 24 V signal interface |
| Maximum supply current | 0.1 A power stage disabled) 6.8 A 24 V 3.8 A 36 V |
| Maximum switching current | 100 mA per output 200 mA total |
| Nominal output power | 45 W 24 V 47 W 36 V |
| Number of motor poles | 6 |
| Phases | Single phase |
| IP degree of protection | IP41 shaft bushing: conforming to IEC 60034-5 IP54 total except shaft bushing: conforming to IEC 60034-5 |
| Communication interface | RS485, Integrated |
| Mounting support | Flange |
| Mounting holes diameter | 0.2 in (4.4 mm) |
| Number of mounting holes | 2 |
| Electrical connection | Printed circuit board connector |
| Shock resistance | 150 m/s² 1000 shocks IEC 60068-2-29 |
| Relative humidity | 15...85 % without condensation |
| Operating altitude | <= 3280.84 ft (1000 m) without derating |
| Vibration resistance | 20 m/s² 10...500 Hz) 10 cycles IEC 60068-2-6 |
| Standards | IEC 61800-3, Ed 2 EN 61800-3:2001, second environment IEC 60072-1 EN 61800-3 : 2001-02 IEC 50178 IEC 61800-3 IEC 50347 |
| Length | 9.02 in (229 mm) |
| Marking | CE |
| Category | US1PC5618288 |
| Shaft end | Hole |
| Second shaft | Without second shaft end |
| Detent torque | 57.5 lbf.in (6.5 N.m) |
| Holding brake | Without |
| Nominal speed | 75 rpm 24 V 75 rpm 36 V |
| Rotor inertia | 430 kg.cm² |
| Accuracy error | +/- 1 point |
| Nominal torque | 51.3 lbf.in (5.8 N.m) 24 V 53.1 lbf.in (6 N.m) 36 V |
| Reduction ratio | 54:1 (1715:32) |
| Device short name | ILE |
| Motor flange size | 2.6 in (66 mm) |
| Peak stall torque | 103.20 lbf.in (11.66 N.m) 36 V 74.52 lbf.in (8.42 N.m) 24 V |
| Transmission rate | 9.6, 19.2 and 38.4 kbauds |
| Service life in hours | 6000 h bearing |
| Associated fuse rating | 10 A |
| Maximum axial force fa | 80 N |
| Number of motor stacks | 1 |
| Continuous stall torque | 69.9 lbf.in (7.9 N.m) |
| Maximum radial force fr | 200 N |
| Centring collar diameter | 1.4 in (36 mm) |
| Maximum mechanical speed | 93 rpm |
| Speed feedback resolution | 12 points/turn motor 0.56° gearbox output |
| Maximum torsional backlash | 1 ° |
| Ambient air temperature for storage | -13...158 °F (-25...70 °C) |
| Ambient air temperature for operation | 122...149 °F (50...65 °C) (with power derating of 2 % per °C) 32...122 °F (0...50 °C) (without derating) |
| Permissible ambient air temperature around the device | 221 °F (105 °C) power amplifier 230 °F (110 °C) motor |
The ILE1R661PB1A6 is a Schneider Lexium integrated drive combining a brushless DC motor with a 54:1 worm gear, delivering 6 N.m at 36 V and a maximum speed of 93 rpm. It communicates via integrated RS485 at 9.6, 19.2 or 38.4 kbauds, carries CE marking, and is rated IP54 total except IP41 at the shaft bushing.
Compared to the BRS368H131ACA, the ILE1R661PB1A6 delivers 6 N.m torque at 36 V and 93 rpm top speed, suited for high-torque low-speed positioning.
No related articles