Skip to main content
Log in
Schneider Electric SH30702M11A2100 — Servo Motors with Brake

Schneider Electric SH30702M11A2100 SH3 Servo Motor, 640 W

MPNSH30702M11A2100
Obsolete

Schneider Electric SH3 servo motor, SH30702M11A2100, 640 W continuous power, 3000 rpm at 400 V three-phase, 2.2 N.m nominal torque, IP65, absolute single-turn SinCos Hiperface encoder, without holding brake.

Schneider Electric SH30702M11A2100 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026

Specifications

SH30702M11A2100 — Identification
ParameterValue
Product typeServo motor
Holding brakeWithout
SH30702M11A2100 — Performance
ParameterValue
Nominal torque19.5 lbf.in (2.2 N.m) 115 V single phase 19.03 lbf.in (2.15 N.m) 230 V single phase 17.97 lbf.in (2.03 N.m) 400 V three phase 17.97 lbf.in (2.03 N.m) 480 V three phase
Nominal output power700 W 115 V single phase 340 W 230 V single phase 660 W 400 V three phase 780 W 480 V three phase
Continuous power640 W
Nominal speed750 rpm 115 V single phase 1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase
Maximum mechanical speed8000 rpm
Continuous stall torque18.06 lbf.in (2.04 N.m) 115...480 V three phase
Peak stall torque67.3 lbf.in (7.6 N.m) 115...480 V three phase
Rotor inertia0.41 kg.cm²
SH30702M11A2100 — Electrical
ParameterValue
Rated supply voltage (Us)115...480 V
Network phases3
PhaseThree phase
Maximum current (Irms)6.0 A
Continuous stall current1.5 A
Torque constant1.36 N.m/A 248 °F (120 °C)
Back-EMF constant95.9 V/krpm 68 °F (20 °C)
Number of motor poles3
Stator resistance16.4 Ohm
Stator inductance41.55 mH
Electrical connectionStraight connector
SH30702M11A2100 — Feedback
ParameterValue
Encoder typeAbsolute single turn SinCos Hiperface
Speed feedback resolution128 periods
SH30702M11A2100 — Mechanical
ParameterValue
Shaft end styleParallel key
Shaft diameter0.4 in (11 mm)
Shaft length0.9 in (23 mm)
Key width0.2 in (4 mm)
Motor flange size2.8 in (70 mm)
Mounting supportInternational standard flange
Length7.4 in (187 mm)
Number of mounting holes4
Mounting-hole diameter0.2 in (5.5 mm)
Mounting-hole bolt circle diameter3.2 in (82 mm)
Centring collar diameter2.4 in (60 mm)
Centring collar depth0.10 in (2.5 mm)
Maximum radial force (Fr)710 N 1000 rpm 560 N 2000 rpm 490 N 3000 rpm 450 N 4000 rpm 410 N 5000 rpm 390 N 6000 rpm
Maximum axial force (Fa)80 N
SH30702M11A2100 — Environmental
ParameterValue
IP degree of protectionIP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5
Cooling methodNatural convection
Winding (copper hot) temperature266 °F (130 °C)

Product details

Motor ratings and supply-voltage dependency

The SH30702M11A2100 is a three-phase servo motor from the SH3 series, rated for 640 W continuous power. Its nominal speed and torque vary with the supply voltage: at 400 V three-phase it delivers 3000 rpm and 2.03 N.m; at 480 V three-phase it reaches 3600 rpm and 2.03 N.m; under 115 V single-phase it runs at 750 rpm with 2.2 N.m. The motor is cooled by natural convection, so no forced-air or liquid cooling is required — a factor for enclosure thermal design.

Encoder and feedback — drive compatibility

The motor is equipped with an absolute single-turn SinCos Hiperface encoder. This feedback type is widely supported by Schneider Electric's Lexium drive family and many third-party servo drives; confirm the drive's encoder interface supports Hiperface before specifying. The electrical connection uses a rotatable right-angled connector, which simplifies cable routing in tight cabinets.

Mechanical interface and mounting

The motor mounts via an international standard flange (70 mm flange size, 60 mm centring collar diameter) with a parallel key shaft end (11 mm shaft diameter, 23 mm shaft length). The centring collar depth is 2.5 mm. Maximum radial force at the shaft is 710 N at 1000 rpm, derating to 390 N at 6000 rpm; maximum axial force is 80 N. These limits govern belt-drive or direct-coupling design.

Environmental protection and compliance

Both the motor body and the shaft bushing are rated IP65 per IEC 60034-5, making the unit suitable for washdown environments and dusty industrial floors.

Frequently asked questions

What is SH30702M11A2100's listed phase and nominal speed?

The motor is a three-phase design. Nominal speed depends on supply voltage: 3000 rpm at 400 V three-phase, 3600 rpm at 480 V three-phase, 750 rpm at 115 V single-phase, and 1500 rpm at 230 V single-phase.

What compliance documentation is available for SH30702M11A2100?

The motor carries an IP65 rating per IEC 60034-5. For RoHS, REACH, and UL documentation, refer to the official Schneider Electric product page or request the declaration of conformity from the supplier.

MPN
SH30702M11A2100