Skip to main content
Log in
Schneider Electric SH30703M11F2200 — Servo Motors with Brake

Schneider Electric SH30703M11F2200 Servo Motor with Brake

MPNSH30703M11F2200
Obsolete

Schneider Electric SH3 series servo motor with brake, SH30703M11F2200, 830 W continuous power, 3 N.m holding torque, IP65/IP67, absolute single-turn SinCos Hiperface encoder, 70 mm flange.

Schneider Electric SH30703M11F2200 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026

Specifications

SH30703M11F2200 — Identification
ParameterValue
Product typeServo motor
Holding brakeWith
SH30703M11F2200 — Performance
ParameterValue
Nominal torque26.99 lbf.in (3.05 N.m) 115 V single phase 26.11 lbf.in (2.95 N.m) 230 V single phase 23.28 lbf.in (2.63 N.m) 400 V three phase 23.28 lbf.in (2.63 N.m) 480 V three phase
Nominal output power240 W 115 V single phase 460 W 230 V single phase 880 W 400 V three phase 1030 W 480 V three phase
Continuous power830 W
Nominal speed750 rpm 115 V single phase 1500 rpm 230 V single phase 3000 rpm 400 V three phase 3600 rpm 480 V three phase
Maximum mechanical speed8000 rpm
Continuous stall torque26.02 lbf.in (2.94 N.m) 115...480 V three phase
Peak stall torque100.01 lbf.in (11.3 N.m) 115...480 V three phase
Holding brake torque26.6 lbf.in (3 N.m)
Rotor inertia0.807 kg.cm²
SH30703M11F2200 — Electrical
ParameterValue
Rated supply voltage (Us)115...480 V
Network phases3
PhaseThree phase
Maximum current (Irms)8.7 A
Continuous stall current2.1 A
Torque constant1.4 N.m/A 248 °F (120 °C)
Back-EMF constant95 V/krpm 68 °F (20 °C)
Number of motor poles3
Stator resistance10.7 Ohm
Stator inductance76.85 mH
Electrical connectionStraight connector
SH30703M11F2200 — Feedback
ParameterValue
Encoder typeAbsolute single turn SinCos Hiperface
Speed feedback resolution128 periods
SH30703M11F2200 — Mechanical
ParameterValue
Shaft end styleParallel key
Shaft diameter0.6 in (14 mm)
Shaft length1.2 in (30 mm)
Key width0.2 in (5 mm)
Motor flange size2.8 in (70 mm)
Mounting supportInternational standard flange
Length10 in (254 mm)
Number of mounting holes4
Mounting-hole diameter0.2 in (5.5 mm)
Mounting-hole bolt circle diameter3.2 in (82 mm)
Centring collar diameter2.4 in (60 mm)
Centring collar depth0.10 in (2.5 mm)
Maximum radial force (Fr)730 N 1000 rpm 580 N 2000 rpm 510 N 3000 rpm 460 N 4000 rpm 430 N 5000 rpm 400 N 6000 rpm
Maximum axial force (Fa)80 N
SH30703M11F2200 — Environmental
ParameterValue
IP degree of protectionIP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5
Cooling methodNatural convection
Winding (copper hot) temperature266 °F (130 °C)

Product details

Motor form factor and mounting constraints

The SH30703M11F2200 mounts on an international standard flange with a 70 mm square pilot diameter and 60 mm centring collar, per IEC 60034-5. The 14 mm shaft carries a parallel key with a 5 mm key width and 30 mm shaft length; the overall body length is 254 mm. For panel integration, the IP65 motor body and shaft bushing, plus IP67 housing, allow direct washdown exposure without a secondary cover — the sealing is on the housing, not just the connector.

Speed and torque across supply voltages

Nominal speed depends on the supply: 750 rpm at 115 V single-phase, 1500 rpm at 230 V single-phase, 3000 rpm at 400 V three-phase, and 3600 rpm at 480 V three-phase. The maximum mechanical speed is 8000 rpm, providing overspeed margin for deceleration or transient conditions. Nominal torque ranges from 2.63 N.m at 400/480 V three-phase up to 3.05 N.m at 115 V single-phase; the holding brake delivers 3 N.m, sufficient to hold a vertical axis or prevent back-driving when power is removed.

Feedback and electrical interface

The encoder is an absolute single-turn SinCos Hiperface type, providing position feedback at power-up without a homing cycle — relevant for applications where the axis position must be known immediately after a power cycle. Electrical connection is via a straight connector or a rotatable right-angled connector, giving flexibility for cable routing in tight cabinets. The motor is three-phase, with 3 poles and a stator inductance of 76.85 mH and resistance of 10.7 Ohm.

Thermal and environmental ratings

Cooling is by natural convection — no external fan, so the motor relies on its own surface area and mounting flange for heat dissipation. The hot-spot copper temperature limit is 130 °C; the torque constant is specified at 120 °C copper temperature, reflecting the operating condition rather than a cold-start value. Continuous stall current is 2.1 A, with a maximum RMS current of 8.7 A. The IP65/IP67 rating means the motor withstands hose-directed water and temporary submersion, suitable for food processing or outdoor conveyor lines where washdown is routine.

Frequently asked questions

What is the holding torque of the brake on SH30703M11F2200?

The holding brake delivers 3 N.m (26.6 lbf.in). This is the static holding torque when the brake is engaged, sufficient to hold a vertical axis load or prevent shaft rotation when power is off.

What encoder feedback does SH30703M11F2200 use?

It uses an absolute single-turn SinCos Hiperface encoder. This provides absolute position within one revolution at power-up, eliminating the need for a homing sequence on each power cycle.

What IP rating does SH30703M11F2200 have?

The motor body and shaft bushing are IP65, and the housing is IP67, all conforming to IEC 60034-5. This means the motor withstands hose-directed water and temporary immersion, suitable for washdown environments.

MPN
SH30703M11F2200