Skip to main content
Omron E5EC-RX4ABM-011

Omron E5EC-RX4ABM-011 Temperature Controller

MPN E5EC-RX4ABM-011
Active

Omron E5EC series temperature controller, E5EC-RX4ABM-011, relay (5) output, 100~240 VAC supply, spring terminal, IP66, panel mount, 92x45 mm cutout.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

E5EC-RX4ABM-011 specifications
ParameterValue
SeriesE5EC
Output signalRelay (5)
Supply voltage100 to 240VAC
IP ratingIP66
MountingPanel Mount
Temp operating max55 °C
Temp operating min-10 °C
Weight0.463 lb (210.01 g)
PackageBox
Control methodOn/Off, Proportional (PID)

Product details

Five relay outputs — what they drive

The E5EC-RX4ABM-011: This controller carries five relay outputs. That means it can switch heaters, cooling contactors, alarm annunciators, and a secondary load directly — no interposing relays needed for most 24-240 VAC circuits. The relay count is the main differentiator from the four-relay E5EC-RX2ASM-800 variant; if your BOM calls for five independent outputs, this is the one. The control method covers On/Off and Proportional (PID) modes. For processes where overshoot matters — plastic extrusion, oven zones, autoclaves — the PID loop with auto-tune handles it. For simple tank or room temperature hold, On/Off is fine and faster to commission.

Sensor input flexibility — 13 TC types plus RTD and process signals

The input range spans -200°C to 2300°C across RTD and thirteen thermocouple types (B, E, J, K, L, N, PLII, R, S, T, U, W) plus 0-20 mA and 0-10 VDC process signals. That covers almost any industrial temperature sensor you'll encounter — from cryogenic RTDs to high-temp R-type TC in a furnace. The process inputs also let it read pressure or level transmitters if the application needs a single-loop controller with a 4-20 mA signal.

IP66 front panel — washdown-ready

The IP66 ingress protection rating means the front panel is dust-tight and protected against water jets — not just splashes. This matters for food-and-beverage lines, washdown stations, outdoor enclosures, or any panel face that gets hosed down. The seal is at the panel gasket, not the housing; the spring terminals on the rear are IP20 as standard.

Spring terminals — tool-less wiring

Termination is spring-clamp, not screw. Solid or ferruled stranded wire pushes in — no screwdriver needed for tightening, no risk of loosening under vibration. For panel builders, this shaves a few seconds per wire and eliminates torque-check steps on the assembly line.

Heater fault detection built in

The E5EC-RX4ABM-011 includes heater fault detection. A current transformer (CT, not included) on the load line feeds back to the controller; if the heater current drops below the set threshold — broken element, failed SSR shorted open — the controller flags it. This is a standard feature on the E5EC series, not an add-on option.

Panel cutout and display

The panel cutout is 92.00 mm x 45.00 mm — standard 1/4 DIN. The LCD display shows three rows of four characters each, with tri-color backlight. The color can change based on process status (green for run, red for alarm, etc.), giving operators a quick visual cue from across the panel.

MPN
E5EC-RX4ABM-011