FX3U-3A-ADP - Mitsubishi Electric
MPNFX3U-3A-ADP
Analog input / output adapter FX3U - 3A - ADP
$150.00Ref. price · indicative, final on quote
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026
Specifications
| Parameter | Value |
|---|---|
| Withstand voltage | Between all terminals and ground terminal: 500 VAC for 1 minute |
| Resolution voltage input | 2.5 mV (10 V x 1/4000) |
| Resolution voltage output | 2.5 mV (10 V x 1/4000) |
| Overall precision voltage input | Ambient temperature 25 ° C ± 5 ° C ± 0.5% (± 50 mV) to full scale 10 V Ambient temperature 0 ° C to 55 ° C ± 1.0% (± 100 mV) to full scale 10 V |
| Overall precision voltage output | Ambient temperature 25 ° C ± 5 ° C ± 0.5% (± 50 mV) to full scale 10 V Ambient temperature 0 ° C to 55 ° C ± 1.0% (± 100 mV) to full scale 10 V External load resistance (Rs) is less than 5 kΩ In addition, the following calculations increase. (It increases by 100 mV per 1%.) 47 X 100 / (Rs + 47) - 0.9 (%) |
| Absolute maximum input voltage input | -0.5 V, +15 V |
| Analog input analog input range voltage input | DC 0 to 10 V (input resistance 198.7 kΩ) |
| Analog output analog output range voltage output | DC 0 to 10 V (external load resistance 5 k to 1 MΩ) |
| Current input | Ambient temperature 25 ° C ± 5 ° C ± 0.5 % (± 80 μA) against full scale 16 mA Ambient temperature 0 ° C to 55 ° C ± 1.0% (± 160 μA) for full scale 16 mA |
| Current output | Ambient temperature 25 ° C ± 5 ° C ± 0.5 % (± 80 μA) against full scale 16 mA Ambient temperature 0 ° C to 55 ° C ± 1.0% (± 160 μA) for full scale 16 mA |
| Interface drive power supply | DC 5 V 20 mA Internal power is supplied from the DC 5 V power supply of the basic unit. |
| Power supply conversion circuit drive power supply | DC24 V + 20% -15% 90 mA Connect a 24 VDC power supply to the terminal block and supply it. |
All specifications
| Parameter | Value |
|---|---|
| Frequency | 57 to 150 Hz : Acceleration: 9.8 m / s 2 10 times in X, Y, Z directions (80 minutes in total) |
| Direct installation frequency | 10 to 57 Hz : One amplitude: 0.075 mm X, Y, Z 10 times in each direction (80 minutes in total) |
| Anti-vibration when DIN rail is installed frequency | 10 to 57 Hz : One amplitude: 0.035 mm X, Y, Z 10 times in each direction (80 minutes in total) |
| Operating temperature | 0 to 55 ° C. ... Operating -25 to 75 ° C. ..... Save |
| Use altitude | Can not be used in an environment pressurized to 2000 m or less under atmospheric pressure. It may break down. |
| Relative humidity | 5 to 95% RH (noncondensing).... in operation |
| Shipping weight | 1.1 Kg |
| Mass | About 0.1 Kg |
| Ground | Class D grounding (grounding resistance: 100 Ω or less)Grounding should be dedicated ground or common ground. |
| Manufacturer | Mitsubishi Electric |
| Digital input | 12 bit binary |
| Digital output | 12 bit binary |
| Noise immunity | Noise voltage with 1,000 Vp-p, noise width 1 μs, rising 1 ns, with noise si |
| Use atmosphere | There is no corrosive property, flammable gas, conductive dust (dust) is not serious |
| Impact resistance | 147 m / s 2 , working time 11 ms, three times in X, Y, Z directions with a sine half-wave pulse |
| Insulation method | . Insulation between analog input / output section and sequencer by photo coupler . Insulation between drive power supply and analog input / output section by DC / DC converter . No isolation between each channel |
| Estimated lead time | 1 - 10 Working Days |
| Application sequencer | FX3S, FX3G (Ver.1.20 or later), FX3U (Ver.2.61 or later), FX3GC, FX3UC (Ver.2.61 or later) FX3S - CNV - ADP is required for connection to FX3S. For connection to FX 3 G, FX 3 G - CNV - ADP is required. To connect to FX3U and FX3UC - 32MT - LT (-2), a function expansion board is required. |
| Input characteristics | Input mode (voltage / current input) can be set for each channel. |
| Insulation resistance | Between all terminals and ground terminal: 500 MV DC 500 MΩ or more with an insulation resistance meter |
| Output characteristics | Output mode (voltage / current output) can be set. |
| Number of input channels | 2 channels |
| Number of output channels | 1 channel |
| Number of occupied i (O points) | 0 point (It does not relate to the maximum input / output point number of the sequencer) |
MPN
FX3U-3A-ADP