Schneider Electric NTSART0603K
MPNNTSART0603K
Active
Temperature Input Module + Base, 6 Differential In, RTD, Thermistor, 2/3 Wires, Modicon Edge I/O NTS
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026
Specifications
| Parameter | Value |
|---|---|
| Type of cable | Shielded cable |
| Range of product | Modicon Edge I/O NTS |
| Power supply type | Bus power from power supply bus (24 Vdc) Field power from power supply field (24 Vdc) |
| Analogue input type | RTD Ni 100/Ni 1000 RTD Pt 100/Pt 1000 RTD Cu 10/50/100 RTD JPt 100/1000 RTD high precision Cu50/100, Ni100/1000, Pt100/1000 Resistor 100 Ohm...32 kOhm Thermistor PTC 100 Ohm...10 kOhm Thermistor NTC 100 Ohm...200 kOhm |
| Input protection type | Over voltage protection |
| Product or component type | Temperature input module kit |
| Rated operational voltage limits | 20.4...28.8 V DC |
| Typical current consumption | 36 mA 24 V DC on the Bus current 25.2 mA 24 V DC on the internal field current minimum 30.2 mA 24 V DC on the internal field current maximum |
| Power dissipation in | 1.6 W maximum at 24 V DC |
| Isolation between field power and bus | 1500 V AC |
| IP degree of protection | IP20 |
| Mounting support | Top hat type TH35-7.5 rail IEC 60715 Top hat type TH35-15 rail IEC 60715 |
All specifications
| Parameter | Value |
|---|---|
| Maximum cable distance between devices | Shielded cable <656.2 ft (200 m) |
| Pollution degree | 2 |
| Shock resistance | 15 g 11 ms with and without accessory) |
| Relative humidity | 5...95 % without condensation |
| Operating altitude | 0...6561.68 ft (0...2000 m) 2000...5000 m with derating |
| Vibration resistance | 1 g without accessory 2 g with accessory |
| Depth | 3.1 in (80 mm) |
| Width | 0.6 in (15 mm) |
| Height | 3.9 in (100 mm) |
| Housing colour | Grey |
| Product weight | 0.161 lb(US) (0.073 kg) |
| Standards | EN/IEC 61131-2 EN 61010-2-201 UL 61010-2-201 IACS E10 EN/IEC 61000-6-5 EN/IEC 61850-3 EN/IEC 60079-0 EN 50155 EN 50121-4 EN 50121-5 |
| Marking | CE UKCA CULus RCM |
| Category | US1PC3318214 |
| Directives | 2014/30/EU - electromagnetic compatibility 2014/34/EU - ATEX directive 2014/35/EU |
| Non-linearity | <= 0.01 % FS RTD |
| Operating mode | Asynchronous |
| Input impedance | 1 MOhm typical |
| Kit composition | NTSART0603 module NTSXBA0100H base |
| Input diagnostic | Underflow error per channel Overflow error per channel Broken wire error per channel Hardware error per channel Calibration error per channel Internal field power supply error per channel |
| Local signalling | 1 LED green module operating (RUN) 1 LED per channel green channel diagnostic 1 LED red module error (ERR) |
| Input wiring mode | 2, 3 or 4 wires for RTD and resistance inputs 2-wire for thermistor NTC/PTC inputs |
| Measurement error | <= 0.10 % FS -20...60 °C (short time sampling) |
| Sampling duration | 60 ms at 50Hz rejection per channel 60 ms at 60Hz rejection per channel 40 ms channel switch time with short time sampling 140 ms channel switch time with long time sampling |
| Temperature drift | ± 0.003 % FS/ °C |
| Device application | Industrial Application |
| Mandatory accessory | NTSXTB18_0_H terminal block |
| Analogue input number | 6 |
| Common mode rejection | 100 dB |
| Hot swapping fallback | Yes |
| Analogue input resolution | 16 bits with overflow |
| Environmental characteristic | Gas resistant C3 and G2 Salt spray resistant |
| Permitted overload on inputs | +/- 2.4 % over voltage range |
| Isolation between channels and bus | 1500 V AC |
| Ambient air temperature for storage | -40...185 °F (-40...85 °C) |
| Ambient air temperature for operation | -4...140 °F (-20...60 °C) |
| Isolation between channels and field pwr | 1000 V AC |
MPN
NTSART0603K