Skip to main content
Log in
Schneider Electric LP2K1201FD3 — Contactors

Schneider TeSys K LP2K1201FD3 Reversing Contactor, 12A AC-3,

MPNLP2K1201FD3
Obsolete

Schneider Electric TeSys K reversing contactor, 3P, AC-3 <= 440 V 12 A, 1 NC, 110 V DC coil, IP20, 57 mm depth.

Schneider Electric LP2K1201FD3 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026

Specifications

LP2K1201FD3 — Identification
ParameterValue
Product / component typeReversing contactor
Series / rangeTeSys
ApplicationMotor control Resistive load
LP2K1201FD3 — Ratings & Performance
ParameterValue
Rated operational voltage (Ue)Power circuit: 690 V AC 50/60 Hz Signalling circuit: 10 MOhm for signalling circuit
Utilisation categoryAC-4 AC-1 AC-3
LP2K1201FD3 — Contacts & Poles
ParameterValue
Pole configuration3P
LP2K1201FD3 — Environmental
ParameterValue
IP degree of protectionIP20 conforming to VDE 0106
Operating altitude2000 m without derating
Mechanical robustnessShocks contactor closed, on Z axis: 15 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor opened, on Z axis: 10 Gn for 11 ms conforming to IEC 60068-2-27 Vibrations contactor closed: 4 Gn, 5...300 Hz conforming to IEC 60068-2-6 Vibrations contactor opened: 2 Gn, 5...300 Hz conforming to IEC 60068-2-6 Shocks contactor opened, on X axis: 10 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor opened, on Y axis: 6 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor closed, on X axis: 15 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor closed, on Y axis: 10 Gn for 11 ms conforming to IEC 60068-2-27
Protective treatment / pollution degreeTC conforming to IEC 60068 TC conforming to DIN 50016
Flame retardanceV1 conforming to UL 94 Requirement 2 conforming to NF F 16-101 Requirement 2 conforming to NF F 16-102
LP2K1201FD3 — Mechanical
ParameterValue
Width90 mm
Height58 mm
Depth57 mm

Product details

Three poles, all normally open, with one NC auxiliary contact built in. The coil pulls in on 110 V DC. Also carries AC-1 resistive loads and AC-4 inching/jogging duty.

Lifecycle reality — obsolete, not gone

This part is marked obsolete by Schneider. No official successor order code appears in the record, so there is no direct drop-in replacement from the factory. If you are holding a line-down situation with a failed reversing contactor on a TeSys K panel, the mechanical footprint and busbar arrangement are specific to this series. A parametric substitute would need to match the 110 V DC coil voltage, the 1 NC auxiliary, and the reversing busbar preassembly.

IP20 finger-safe terminals per VDE 0106, so it lives inside an enclosure, not exposed. The preassembled reversing busbar means the power wiring between the two contactor halves is already done; you land your incoming three-phase supply and the motor leads on the line and load terminals. Storage range is wider at -50 to 80 °C. Flame retardance meets UL 94 V1 and NF F 16-101/102, which matters for rail and transit applications.

Frequently asked questions

What are the key ratings for the LP2K1201FD3?

Three-pole reversing contactor rated AC-3 at 12 A up to 440 V, with a 110 V DC coil and one NC auxiliary contact. The preassembled reversing busbar is included. IP20 protection, 57 mm deep, DIN-rail mount.

What compliance documentation does this part carry?

Flame retardance rated V1 per UL 94, and also meets NF F 16-101 and NF F 16-102 for rail rolling stock. Protective treatment conforms to IEC 60068 and DIN 50016. IP20 per VDE 0106.

MPN
LP2K1201FD3