Skip to main content
Log in
Schneider Electric LP2K1210MD — Contactors

TeSys LP2K1210MD reversing contactor, 3P, AC-3 12 A, 220 V D

MPNLP2K1210MD
Active

Schneider Electric TeSys K reversing contactor, 3P, AC-3 ≤440 V 12 A, 1 NO, 220 V DC coil, IP20, 57 mm depth.

Schneider Electric LP2K1210MD datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

LP2K1210MD — Identification
ParameterValue
Product / component typeReversing contactor
Series / rangeTeSys
ApplicationResistive load Motor control
LP2K1210MD — Ratings & Performance
ParameterValue
Rated operational voltage (Ue)Power circuit: 690 V AC 50/60 Hz Signalling circuit: 10 MOhm for signalling circuit
Utilisation categoryAC-1 AC-3 AC-4
LP2K1210MD — Contacts & Poles
ParameterValue
Pole configuration3P
LP2K1210MD — Environmental
ParameterValue
IP degree of protectionIP20 conforming to VDE 0106
Operating altitude2000 m without derating
Mechanical robustnessShocks contactor closed, on Z axis: 15 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor opened, on Z axis: 10 Gn for 11 ms conforming to IEC 60068-2-27 Vibrations contactor closed: 4 Gn, 5...300 Hz conforming to IEC 60068-2-6 Vibrations contactor opened: 2 Gn, 5...300 Hz conforming to IEC 60068-2-6 Shocks contactor opened, on X axis: 10 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor opened, on Y axis: 6 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor closed, on X axis: 15 Gn for 11 ms conforming to IEC 60068-2-27 Shocks contactor closed, on Y axis: 10 Gn for 11 ms conforming to IEC 60068-2-27
Protective treatment / pollution degreeTC conforming to IEC 60068 TC conforming to DIN 50016
Flame retardanceV1 conforming to UL 94 Requirement 2 conforming to NF F 16-101 Requirement 2 conforming to NF F 16-102
LP2K1210MD — Mechanical
ParameterValue
Width90 mm
Height58 mm
Depth57 mm

Product details

AC-1 (resistive) and AC-4 (inching/plugging) categories are also listed, so the same block covers heater banks or frequent reversing duty if derated. The power circuit is rated for 690 V AC 50/60 Hz, giving headroom on 480 V or 600 V line supplies. IP20 finger protection (VDE 0106) means it is safe for open-panel mounting but not for washdown environments — install inside an enclosure if moisture or dust is present. The 57 mm depth and 90 mm width fit a standard DIN-rail footprint alongside other TeSys K auxiliaries.

This reversing contactor is pre-wired with the reversing busbar, so it saves a wiring step during panel build — just land the motor leads and coil control wires. The 220 V DC coil suits battery-backed or DC-switched control circuits common in industrial truck, crane, or solar-pump panels.

Frequently asked questions

What are the key electrical ratings I need to check for fit?

The critical rating is AC-3 motor-switching current: 12 A at ≤440 V. The coil is 220 V DC. The power circuit is rated for 690 V AC 50/60 Hz maximum. Utilisation categories also include AC-1 (resistive) and AC-4 (inching/plugging), so derate accordingly for those loads.

What is the physical size of this contactor?

Depth is 57 mm, width 90 mm, height 58 mm. It is IP20 finger-protected and mounts on standard DIN rail within a control panel.

What compliance documentation is available for this part?

The part carries V1 flame retardance per UL 94 and conforms to NF F 16-101/102. Protective treatment conforms to IEC 60068 and DIN 50016. Mechanical robustness is tested to IEC 60068-2-27 (shock) and IEC 60068-2-6 (vibration). IP20 per VDE 0106.

MPN
LP2K1210MD