Skip to main content
Siemens 3RW5077-2AB04

Siemens 3RW5077-2AB04 Soft Starter, 240 A, 200-480 V, ATEX

MPN 3RW5077-2AB04
Active

Siemens 3RW5077-2AB04 hybrid soft starter, 240 A minimum, 200-480 V AC, 24 V DC control, Trip Class 10A/10E/20E, ATEX, IECEx, UL, CSA, CE, PROFIBUS, Modbus RTU/TCP, EtherNet/IP, PROFINET, 282 x 160 x 230 mm.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

3RW5077-2AB04 specifications
ParameterValue
Mountingscrew fixing
Depth282 mm
Width160 mm
Height230 mm
Trip classCLASS 10 A / 10E (preset) / 20E; acc. to IEC 60947-4-2
Service factor1
Digital output version2 normally-open contacts (NO) / 1 changeover contact (CO)

Product details

240 A minimum, Trip Class 10A/10E/20E — overload protection profile

The 3RW5077-2AB04: Rated for a minimum operating current of 240 A, with trip classes 10A, 10E (preset), and 20E selectable per IEC 60947-4-2. This matches common global industrial voltages — 208 V, 230 V, 400 V, 480 V — without needing a separate control transformer for the logic.

Fieldbus integration — PROFIBUS, Modbus, EtherNet/IP, PROFINET

Onboard communication includes PROFIBUS, Modbus RTU, Modbus TCP, EtherNet/IP, and PROFINET with PROFIenergy support. No separate gateway module is required for most PLC ecosystems — the soft starter connects directly to Siemens S7, Rockwell ControlLogix, or third-party controllers over the respective fieldbus. The analog output is configurable as 4-20 mA (default) or 0-10 V, providing motor current or load feedback to a PLC analog input or local HMI. Parameterization of the output type requires the High Feature HMI accessory.

ATEX, IECEx, UL, CSA, CE — compliance for hazardous and global installations

Listed with ATEX and IECEx certification for use in potentially explosive atmospheres (gas and dust). The soft starter can be installed in Zone 2 or Zone 22 areas when properly integrated into the motor circuit — the ATEX mark (Yes) confirms the device meets the essential health and safety requirements of the ATEX directive. CE marking confirms compliance with the Low Voltage Directive and EMC Directive for European markets.

Physical dimensions and mounting — 282 mm depth, screw fixing

Dimensions are 282 mm depth, 160 mm width, 230 mm height. Fastening method is screw fixing (not DIN rail snap-on) — the unit bolts directly to a backplate or mounting panel. Clearance requirements: 100 mm upwards, 10 mm forwards, 0 mm backwards, 75 mm downwards, 5 mm at the sides. Mounting position allows vertical surface with ±90° rotation and ±22.5° tilt forward/backward.

Motor starting profiles — soft torque, voltage ramp, pump ramp down

Supports soft torque (torque-controlled start for gentle acceleration), voltage ramp (adjustable initial voltage and ramp time), and pump ramp down (controlled deceleration to prevent water hammer). These profiles are selected via the onboard HMI or fieldbus parameters. Minimum load is 15 % of the smallest settable Ie — the soft starter can handle lightly loaded motors without dropping out. Remote reset is available by cycling the 24 V control supply. Auto-reset is also supported for unattended restarts after a fault clears.

MPN
3RW5077-2AB04